New Generation of High-efficiency Solar Thermal Absorbers Developed
June 16, 2016 | University of BristolEstimated reading time: 1 minute
Researchers from the Universities of Bristol and Exeter are one step closer to developing a new generation of low-cost, high-efficiency solar cells. The structure is one of the world's first examples of a tri-layer metasurface absorber using a carbon interlayer.
The system, developed by Chenglong Wang a PhD student in Professor Martin Cryan's research group, uses amorphous carbon as an inter-layer between thin gold films with the upper film patterned with a 2D periodic array using focused ion beam etching.
The trilayer gold-carbon-gold metasurface strongly absorbs light across the solar spectrum but minimises emission of thermal radiation from the structure. The use of gold in the research is a first step towards a high temperature metasurface where gold can be replaced by other refractory metals such as tungsten or chrome.
The cell will be used for solar thermal energy applications and has the potential to reach much higher temperatures than simple black surfaces because it can minimise the emission of thermal radiation.
The metasurface has been developed as part of a joint project, led by Dr Neil Fox, between Bristol's Department of Electrical and Electronic Engineering and Schools of Physics and Chemistry. The aim of this project is to develop diamond-based solar thermionic devices, which use sunlight to get surfaces sufficiently hot that they emit electrons directly into a vacuum. If these electrons are collected at a cooled anode, electrical energy can be produced with maximum efficiencies predicted to be much higher than is achievable using conventional silicon solar cells.
Martin Cryan, Professor of Applied Electromagnetics and Photonics in the Department of Electrical and Electronic Engineering, said: "Integrating diamond within metasurfaces is very challenging, and this paper is a first step in that direction using amorphous carbon. The next stage is to carry out high temperature testing on the structures and to attempt to reach the ~700 degrees celsius required to obtain efficient thermionic emission."
The Bristol team have been working with Professor Tapas Mallick from the University of Exeter to develop the low-cost solar concentrator systems.
Suggested Items
SCHMID Group to Exhibit at productronica
11/07/2023 | SCHMID GroupThe SCHMID Group, a global solution provider for the high-tech electronics, photovoltaics, glass and energy systems industries, will be exhibiting at productronica in Munich from November 14 – 17, 2023.
Sigma Mecer: Turning Copper ‘Green’
10/05/2023 | Nolan Johnson, PCB007 MagazineAndreas Littorin is CEO at Sigma Engineering AB. The company has been manufacturing equipment for the PCB industry for 45 years, mainly a mature product for copper recycling of alkaline and acidic etchants in the PCB manufacturing process.
Smart Factory Insights: The Smart Business Case for Local PCB Manufacturing
09/27/2023 | Michael Ford -- Column: Smart Factory InsightsThe PCB has become a neglected component from the Smart assembly manufacturing perspective, wrongly regarded as just a “given” material. We need to put it right. PCB manufacturing needs to become Smart in order to make the local fabrication business model work as part of the holistic electronics’ “smarter, secure, and sustainable” approach—what I’m calling the new three Ss of manufacturing.
Atotech to Participate at KPCA Show 2023 in Seoul, South Korea
08/28/2023 | AtotechMKS’ Atotech will participate at this year’s KPCA Show 2023 in Seoul, South Korea, which will be held at Incheon Songdo Convensia from September 6-8, 2023.
Connect the Dots: Best Drilling Practices for Better PCB Manufacturing
09/05/2023 | Matt Stevenson -- Column: Connect the DotsDrilling is one of the most fundamental steps in the printed circuit board manufacturing process. Until the advent of the through-hole, PCBs were all single-sided with traces and components located on one side. With double-sided and multilayered boards so common now, a PCB without holes doesn't seem like a PCB at all. The drilling process creates the holes that connect the different layers of the PCB. Those holes allow for the connection of components. In fact, without holes, a double-sided PCB is just a coaster.