More Power to You
July 27, 2016 | University of UtahEstimated reading time: 2 minutes
Engineers from the University of Utah and the University of Minnesota have discovered that interfacing two particular oxide-based materials makes them highly conductive, a boon for future electronics that could result in much more power-efficient laptops, electric cars and home appliances that also don't need cumbersome power supplies.
Their findings were published this month in the scientific journal, APL Materials, from the American Institute of Physics.
The team led by University of Utah electrical and computer engineering assistant professor Berardi Sensale-Rodriguez and University of Minnesota chemical engineering and materials science assistant professor Bharat Jalan revealed that when two oxide compounds -- strontium titanate (STO) and neodymium titanate (NTO) -- interact with each other, the bonds between the atoms are arranged in a way that produces many free electrons, the particles that can carry electrical current. STO and NTO are by themselves known as insulators -- materials like glass -- that are not conductive at all.
But when they interface, the amount of electrons produced is a hundred times larger than what is possible in semiconductors. "It is also about five times more conductive than silicon [the material most used in electronics]," Sensale-Rodriguez says.
This innovation could greatly improve power transistors -- devices in electronics that regulate the electrical current --by making power supplies much more efficient for items ranging from televisions and refrigerators to handheld devices, Sensale-Rodriguez says. Today, electronics manufacturers use a material called gallium nitride for transistors in power supplies and other electronics that carry large electrical currents. But that material has been explored and optimized for many years and likely cannot be made more efficient. In this discovery made by the Utah and Minnesota team, the interface between STO and NTO can be at the very least as conductive as gallium nitride and likely will be much more in the future.
"When I look at the future, I see that we can perhaps improve conductivity by an order of magnitude through optimizing of the materials growth," Jalan says. "We are bringing the possibility of high power, low energy oxide electronics closer to reality."
Power transistors that use this combination of materials could lead to smaller devices and appliances because their power supplies would be more energy efficient. Laptop computers, for example, could ditch the bulky external power supplies -- the big black boxes attached to the power cords -- in favor of smaller supplies that are instead built inside the computer. Large appliances that consume a lot of electricity such as air conditioners could be more power efficient. And because there is less power wasted (wasted electricity usually dissipates into heat), these devices will not run as hot as before, says Sensale-Rodriguez. He also believes that if more electronics use these materials for transistors, collectively it could save significant amounts of electricity for the country.
"It's fundamentally a different road toward power electronics, and the results are very exciting" he says. "But we still need to do more research."
Suggested Items
Book Excerpt: The Printed Circuit Assembler’s Guide to... Factory Analytics
04/24/2024 | I-Connect007 Editorial TeamIn our fast-changing, deeply competitive, and margin-tight industry, factory analytics can be the key to unlocking untapped improvements to guarantee a thriving business. On top of that, electronics manufacturers are facing a tremendous burden to do more with less. If you don't already have a copy of this book, what follows is an excerpt from the introduction chapter of 'The Printed Circuit Assembler’s Guide to... Factory Analytics: Unlocking Efficiency Through Data Insights' to whet your appetite.
Listen Up! The Intricacies of PCB Drilling Detailed in New Podcast Episode
04/25/2024 | I-Connect007In episode 5 of the podcast series, On the Line With: Designing for Reality, Nolan Johnson and Matt Stevenson continue down the manufacturing process, this time focusing on the post-lamination drilling process for PCBs. Matt and Nolan delve into the intricacies of the PCB drilling process, highlighting the importance of hole quality, drill parameters, and design optimization to ensure smooth manufacturing. The conversation covers topics such as drill bit sizes, aspect ratios, vias, challenges in drilling, and ways to enhance efficiency in the drilling department.
Elevating PCB Design Engineering With IPC Programs
04/24/2024 | Cory Blaylock, IPCIn a monumental stride for the electronics manufacturing industry, IPC has successfully championed the recognition of the PCB Design Engineer as an official occupation by the U.S. Department of Labor (DOL). This pivotal achievement not only underscores the critical role of PCB design engineers within the technology landscape, but also marks the beginning of a transformative journey toward nurturing a robust, skilled workforce ready to propel our industry into the future.
Winner of The Science Show Rakett 69 Receives Incap Scholarship
04/24/2024 | IncapThe winner of the Rakett 69 science show, Andri Türkson, who stood out as an electronics enthusiast, received a scholarship from Incap Estonia, along with an internship opportunity in Saaremaa.
Alternative Manufacturing Inc. Awarded QML Requalification to IPC J-STD-001 and IPC-A-610
04/24/2024 | IPCIPC's Validation Services Program has awarded an IPC J-STD-001 and IPC-A-610 Qualified Manufacturers Listing (QML) requalification to Alternative Manufacturing Inc (AMI).