Major Advance in Solar Cells Made From Cheap, Easy-To-Use Perovskite
November 9, 2016 | University of California - BerkeleyEstimated reading time: 4 minutes
Solar cells made from an inexpensive and increasingly popular material called perovskite can more efficiently turn sunlight into electricity using a new technique to sandwich two types of perovskite into a single photovoltaic cell.
This first version of a new layered perovskite solar cell already achieves an efficiency of more than 20 percent, rivaling many commercial solar cells. Flexible and easy to make, it can produce more than half a volt of electricity.
Perovskite solar cells are made of a mix of organic molecules and inorganic elements that together capture light and convert it into electricity, just like today's more common silicon-based solar cells. Perovskite photovoltaic devices, however, can be made more easily and cheaply than silicon and on a flexible rather than rigid substrate. The first perovskite solar cells could go on the market next year, and some have been reported to capture 20% of the sun's energy.
In a paper appearing online today in advance of publication in the journal Nature Materials ("Graded bandgap perovskite solar cells"), University of California, Berkeley, and Lawrence Berkeley National Laboratory scientists report a new design that already achieves an average steady-state efficiency of 18.4%, with a high of 21.7% and a peak efficiency of 26%.
"We have set the record now for different parameters of perovskite solar cells, including the efficiency," said senior author Alex Zettl, a UC Berkeley professor of physics, senior faculty member at Berkeley Lab and member of the Kavli Energy Nanosciences Institute. "The efficiency is higher than any other perovskite cell - 21.7% - which is a phenomenal number, considering we are at the beginning of optimizing this."
"This has a great potential to be the cheapest photovoltaic on the market, plugging into any home solar system," said Onur Ergen, the lead author of the paper and a UC Berkeley physics graduate student.
The efficiency is also better than the 10-20% efficiency of polycrystalline silicon solar cells used to power most electronic devices and homes. Even the purest silicon solar cells, which are extremely expensive to produce, topped out at about 25%efficiency more than a decade ago.
The achievement comes thanks to a new way to combine two perovskite solar cell materials - each tuned to absorb a different wavelength or color of sunlight - into one "graded bandgap" solar cell that absorbs nearly the entire spectrum of visible light. Previous attempts to merge two perovskite materials have failed because the materials degrade one another's electronic performance.
"This is realizing a graded bandgap solar cell in a relatively easy-to-control and easy-to-manipulate system," Zettl said. "The nice thing about this is that it combines two very valuable features - the graded bandgap, a known approach, with perovskite, a relatively new but known material with surprisingly high efficiencies - to get the best of both worlds."
Full-spectrum solar cells
Materials like silicon and perovskite are semiconductors, which means they conduct electricity only if the electrons can absorb enough energy - from a photon of light, for example - to kick them over a forbidden energy gap or bandgap. These materials preferentially absorb light at specific energies or wavelengths - the bandgap energy - but inefficiently at other wavelengths.
Cross section of the new solar cell, showing the two perovskite layers (beige and red) separated by a single-atom layer of boron nitride and the thicker graphene aerogel (dark gray), which prevents moisture from destroying the perovskite. Gallium nitride (blue) and gold (yellow) electrodes channel the electrons generated when light hits the solar cell.
"In this case, we are swiping the entire solar spectrum from infrared through the entire visible spectrum," Ergen said. "Our theoretical efficiency calculations should be much, much higher and easier to reach than for single-bandgap solar cells because we can maximize coverage of the solar spectrum."
The key to mating the two materials into a tandem solar cell is a single-atom thick layer of hexagonal boron nitride, which looks like a layer of chicken wire separating the perovskite layers from one other. In this case, the perovskite materials are made of the organic molecules methyl and ammonia, but one contains the metals tin and iodine, while the other contains lead and iodine doped with bromine. The former is tuned to preferentially absorb light with an energy of 1 electron volt (eV) - infrared, or heat energy - while the latter absorbs photons of energy 2 eV, or an amber color.
The monolayer of boron nitride allows the two perovskite materials to work together and make electricity from light across the whole range of colors between 1 and 2 eV.
The perovskite/boron nitride sandwich is placed atop a lightweight aerogel of graphene that promotes the growth of finer-grained perovskite crystals, serves as a moisture barrier and helps stabilize charge transport though the solar cell, Zettl said. Moisture makes perovskite fall apart.
The whole thing is capped at the bottom with a gold electrode and at the top by a gallium nitride layer that collects the electrons that are generated within the cell. The active layer of the thin-film solar cell is about 400 nanometers thick.
"Our architecture is a bit like building a quality automobile roadway," Zettl said. "The graphene aerogel acts like the firm, crushed rock bottom layer or foundation, the two perovskite layers are like finer gravel and sand layers deposited on top of that, with the hexagonal boron nitride layer acting like a thin-sheet membrane between the gravel and sand that keeps the sand from diffusing into or mixing too much with the finer gravel. The gallium nitride layer serves as the top asphalt layer."
It is possible to add even more layers of perovskite separated by hexagonal boron nitride, though this may not be necessary, given the broad-spectrum efficiency they've already obtained, the researchers said.
"People have had this idea of easy-to-make, roll-to-roll photovoltaics, where you pull plastic off a roll, spray on the solar material, and roll it back up," Zettl said. "With this new material, we are in the regime of roll-to-roll mass production; it's really almost like spray painting."
Suggested Items
Real Time with... IPC APEX EXPO 2024: Sustainability in the Industry
04/26/2024 | Real Time with...IPC APEX EXPOGuest Editor Henry Crandall and Chris Nash of Indium Corporation discuss the company's 90th anniversary and its focus on sustainability. They focus on the benefits of sustainable materials, their compatibility, and value propositions. The conversation also highlights how Durafuse LT technology's role in reducing reflow temperatures is leading to significant cost and energy savings. Nash also touches on downstream sustainability efforts such as using recycled materials for packaging.
SMC Korea 2024 to Highlight Semiconductor Materials Trends and Innovations on Industry’s Path to $1 Trillion
04/24/2024 | SEMIWith Korea a major consumer of semiconductor materials and advanced materials a key driver of innovation on the industry’s path to $1 trillion, industry leaders and experts will gather at SMC (Strategic Materials Conference) Korea 2024 on May 29 at the Suwon Convention Center in Gyeonggi-do, South Korea to provide insights into the latest materials developments and trends. Registration is open.
Groundbreaking Ceremony Marks the Beginning of a New Era for Newccess Industrial; The Construction of the MINGXIN Building
04/12/2024 | Newccess IndustrialOn a clear and sunny day in March, the groundbreaking ceremony for the MINGXIN Building took place in Shenzhen, China. This moment marked the official commencement of construction for a project that will reshape the semiconductor materials industry.
The Need for a Holistic Global Sustainability Standard
04/10/2024 | Michael Ford, Aegis SoftwareNo one can deny that the resources of our fragile planet are finite. The environment seems like a third party, subject to constant degradation. We’re acutely aware of the effects of pollution on our climate, and despite our “throw-away” culture, recycling and recovery of materials has remained relatively expensive, even as we use more energy just to survive.
iNEMI Publishes Four Roadmap Topics
04/04/2024 | iNEMIThe International Electronics Manufacturing Initiative (iNEMI) announces the availability of the first roadmap topics in the new iNEMI Roadmap format. Printed circuit boards, sustainable electronics, smart manufacturing, and mmWave materials and test are now available online.