Reducing Read Errors More Than a Bit
February 10, 2017 | A*STAREstimated reading time: 2 minutes
While we aspire to store increasing amounts of digital data on ever smaller devices, conventional memory technologies based on electron charge are reaching a physical limit on how much they can store in a given space. Alternative storage methods are urgently needed.
Kien Trinh, Sergio Ruocco and Massimo Alioto at the A*STAR Data Storage Institute and National University of Singapore are investigating a promising storage technique called spin-transfer torque magnetic random-access memory (STT-MRAM). In their pursuit, the researchers have developed a voltage-boosting scheme for an STT-MRAM system, which greatly reduces errors incurred when reading data.
STT-MRAM works by exploiting electrons’ intrinsic angular momentum, or spin, rather than their charge. Electron spin can take only two values — up or down — and a standard electrical current contains approximately equal numbers of each. STT-MRAM uses a spin-polarized current, which has more of one spin type than the other, to exert a torque on magnetized ‘bitcells’. This flips the bitcell orientation to high or low states and thereby writes binary data. To read data, the surrounding circuitry must then detect small changes in the resistance of the bitcell, a difficult task to achieve without errors.
“In the physical process of reading STT-MRAM there is an established trade-off between read disturbance (the chance of unintentionally flipping the bitcell when you read it) and read decision (reading the wrong value currently stored in the bitcell),” says Trinh. “To lower the read disturbance, the read current has to be small. However, a larger read current helps us distinguish between the high and low resistance states of the bitcell.” In other words, if you reduce one error, you increase the other.
Trinh and co-workers trialed a new read scheme in which the voltage in the system was boosted by switched capacitors. They performed extensive statistical simulations to find optimum electronic design settings that minimize the impact of natural variations.
“We achieved a rate of just one error per billion bitcell reads, compared to the conventional sensing scheme which has one per ten million,” says Alioto. “What’s more, our system is one of the first that can achieve so few errors while remaining suitable for low-power and low-voltage applications.”
The team are hopeful they can prove their design concepts on real devices in the near future, and contribute to the commercialization of this emerging technology. “We think STT-MRAM could be available on the consumer market within three to five years,” says Ruocco.
The A*STAR-affiliated researchers contributing to this research are from the Data Storage Institute. For more information about the team’s research, please visit the GREEN IC (Green Resilient Energy Efficient Nanoscale Integrated Circuits) webpage.
Suggested Items
Lockheed Martin Australia, The Department Of Defence Sign Strategic Partnership Head Contract
04/26/2024 | Lockheed MartinLockheed Martin Australia signed a landmark AUD$500 million contract with the Department of Defence to build Australia’s future Joint Air Battle Management System under project - AIR6500 Phase 1 (AIR6500-1).
Cadence, TSMC Collaborate on Wide-Ranging Innovations to Transform System and Semiconductor Design
04/25/2024 | Cadence Design SystemsCadence Design Systems, Inc. and TSMC have extended their longstanding collaboration by announcing a broad range of innovative technology advancements to accelerate design, including developments ranging from 3D-IC and advanced process nodes to design IP and photonics.
Siemens’ Breakthrough Veloce CS Transforms Emulation and Prototyping with Three Novel Products
04/24/2024 | Siemens Digital Industries SoftwareSiemens Digital Industries Software launched the Veloce™ CS hardware-assisted verification and validation system. In a first for the EDA (Electronic Design Automation) industry, Veloce CS incorporates hardware emulation, enterprise prototyping and software prototyping and is built on two highly advanced integrated circuits (ICs) – Siemens’ new, purpose-built Crystal accelerator chip for emulation and the AMD Versal™ Premium VP1902 FPGA adaptive SoC (System-on-a-chip) for enterprise and software prototyping.
Taiyo Circuit Automation Installs New DP3500 into Fuba Printed Circuits, Tunisia
04/25/2024 | Taiyo Circuit AutomationTaiyo Circuit Automation is proud to be partnered with Fuba Printed Circuits, Tunisia part of the OneTech Group of companies, a leading printed circuit board manufacturer based out of Bizerte, Tunisia, on their first installation of Taiyo Circuit Automation DP3500 coater.
Vicor Power Orders Hentec Industries/RPS Automation Pulsar Solderability Testing System
04/24/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, is pleased to announce that Vicor Power has finalized the purchase of a Pulsar solderability testing system.