Extracting Energy From Multiple Sources Could Help Power Wearable Technology
February 13, 2017 | AIP.orgEstimated reading time: 2 minutes
Many forms of energy surround you: sunlight, the heat in your room and even your own movements. All that energy -- normally wasted -- can potentially help power your portable and wearable gadgets, from biometric sensors to smart watches. Now, researchers from the University of Oulu in Finland have found that a mineral with the perovskite crystal structure has the right properties to extract energy from multiple sources at the same time.
Perovskites are a family of minerals, many of which have shown promise for harvesting one or two types of energy at a time -- but not simultaneously. One family member may be good for solar cells, with the right properties for efficiently converting solar energy into electricity. Meanwhile, another is adept at harnessing energy from changes in temperature and pressure, which can arise from motion, making them so-called pyroelectric and piezoelectric materials, respectively.
Sometimes, however, just one type of energy isn't enough. A given form of energy isn't always available -- maybe it's cloudy or you're in a meeting and can't get up to move around. Other researchers have developed devices that can harness multiple forms of energy, but they require multiple materials, adding bulk to what's supposed to be a small and portable device.
This week in Applied Physics Letters, from AIP Publishing, Yang Bai and his colleagues at the University of Oulu explain their research on a specific type of perovskite called KBNNO, which may be able to harness many forms of energy. Like all perovskites, KBNNO is a ferroelectric material, filled with tiny electric dipoles analogous to tiny compass needles in a magnet.
When ferroelectric materials like KBNNO undergo changes in temperature, their dipoles misalign, which induces an electric current. Electric charge also accumulates according to the direction the dipoles point. Deforming the material causes certain regions to attract or repel charges, again generating a current.
Previous researchers have studied KBNNO's photovoltaic and general ferroelectric properties, but they did so at temperatures a couple hundred degrees below freezing, and they didn't focus on properties related to temperature or pressure. The new study represents the first time anyone has evaluated all of these properties at once above room temperature, Bai said.
The experiments showed that while KBNNO is reasonably good at generating electricity from heat and pressure, it isn't quite as good as other perovskites. Perhaps the most promising finding, however, is that the researchers can modify the composition of KBNNO to improve its pyroelectric and piezoelectric properties. "It is possible that all these properties can be tuned to a maximum point," said Bai, who, with his colleagues, is already exploring such an improved material by preparing KBNNO with sodium.
Within the next year, Bai said, he hopes to build a prototype multi-energy-harvesting device. The fabrication process is straightforward, so commercialization could come in just a few years once researchers identify the best material.
"This will push the development of the Internet of Things and smart cities, where power-consuming sensors and devices can be energy sustainable," he said.
This kind of material would likely supplement the batteries on your devices, improving energy efficiency and reducing how often you need to recharge. One day, Bai said, multi-energy harvesting may mean you won't have to plug in your gadgets anymore. Batteries for small devices may even become obsolete.
About American Institute of Physics
Applied Physics Letters features concise, rapid reports on significant new findings in applied physics. The journal covers new experimental and theoretical research on applications of physics phenomena related to all branches of science, engineering, and modern technology.
Suggested Items
New Book on Low-temperature Soldering Now Available
04/17/2024 | I-Connect007I-Connect007 is pleased to announce that The Printed Circuit Assembler’s Guide to… Low-temperature Soldering, Vol. 2, by subject matter experts at MacDermid Alpha Electronics Solutions, is now available for download.
The Chemical Connection: Reducing Etch System Water Usage, Part 1
04/05/2024 | Don Ball -- Column: The Chemical ConnectionWater conservation has become an important component of the overall system design for most manufacturing operations today. Changing climate conditions and increasing populations are beginning to strain the freshwater supplies in many areas of the country. As a result, as equipment suppliers, we see an increasing number of requests for options that reduce water usage in proposed wet processing systems. Etching systems tend to use more water because of the need for close temperature control to maintain steady etch rates and the rinsing requirements for complete removal of corrosive etchants from the surface of the product before the next process step. This column contains some simple suggestions for reducing water usage in etch systems that won’t strain the budget too much.
Indium’s Sze Pei Lim to Present on Semiconductor Packaging at ICEP Japan
04/02/2024 | Indium CorporationIndium Corporation’s Senior Global Product Manager for Semiconductor and Advanced Materials, Sze Pei Lim, is scheduled to present at the International Conference on Electronics Packaging (ICEP 2024).
Nihon Superior Sets New Standards in Lead-Free Soldering Technology at APEX 2024
03/13/2024 | PVANihon Superior Co. Ltd., an advanced joining material supplier, will exhibit in Booth 1325 during the 2024 IPC APEX EXPO, scheduled to take place April 9-11, 2024 at the Anaheim Convention Center in California.
Indium Corporation to Showcase Proven EV Products and High-Reliability Alloys at Productronica China
02/28/2024 | Indium CorporationAs a materials pioneer and trusted partner in electric vehicle (EV) and e-Mobility manufacturing, Indium Corporation is proud to showcase its high-reliability alloys and soldering solutions at Productronica China, March 20-22, in Shanghai.