Laser Heating Hits the Spot
February 24, 2017 | A*STAREstimated reading time: 2 minutes
Laser-based measurements reveal just how small each magnetic ‘bit’ could be using the next generation hard disk technology known as heat-assisted magnetic recording
Heat-assisted magnetic recording could be the basis of the next generation of hard disk drive technologies. Stewart Waller/Getty
A method for accurately measuring the thermomagnetic properties of heat-assisted magnetic recording (HAMR) media reveals what the minimum bit size and ultimate data density might be for this next generation storage technology.
Existing hard disk technology is approaching fundamental physical limits on the amount of data that can be stored on magnetic disks. One of the most promising technologies capable of breaching these limits is HAMR, which heats small areas to allow for smaller magnetic bits and higher data densities. The minimum possible bit size has been the subject of considerable debate. Yang Hongzhi and Yunjie Chen from the A*STAR Data Storage Institute (DSI) have now developed a method using two lasers to put this debate to rest.
“The basic idea of HAMR is to use a tiny laser spot to heat the magnetic material on the disk to its critical ‘Curie’ temperature, which makes it more easily writable,” explains Chen.
Writability sets the upper limit on data density as it determines how small an area can be magnetically ‘switched’ using the weak magnetic field of conventional data writing heads. By heating the magnetic disk to a certain temperature, a material with an intrinsically finer-grained magnetic fabric can be used, resulting in smaller bits. One of the unknowns surrounding the technology is how far each bit would need to be separated in order to maintain reliable switching without affecting neighboring bits.
“The switching field distribution at the heating temperature is directly related to how narrow a magnetic transition can be recorded, which will decide the data density that could be achieved,” says Chen. “Using a lab-built multifunctional HAMR writing and measurement system here at the DSI, we developed a method that allows us to accurately measure the thermomagnetic properties of HAMR media at the Curie temperature.”
The team’s approach uses two laser beams, one to spot-heat the media to exactly the right temperature, and the other to measure the magnetic signal based on an unusual interaction between magnetism and light known as the magneto-optic Kerr effect.
Using this approach, the researchers were able to run a range of tests on experimental HAMR media, providing unprecedented insight into its thermomagnetic response. “We expect this test method to be helpful for characterization and development of HAMR media as the major candidate for the next generation of hard disk drive technologies.”
Suggested Items
Koh Young Showcases Award-winning Inspection Solutions at SMTconnect with SmartRep in Hall 4A.225
04/25/2024 | Koh Young TechnologyKoh Young Technology, the industry leader in True 3D measurement-based inspection solutions, will showcase an array of award-winning inspection and measurement solutions at SMTconnect alongside its sales partner, SmartRep, in booth 4A.225 at NürnbergMesse from June 11-13, 2023. The following offers a glimpse into what Koh Young will present at the tradeshow:
Book Excerpt: The Printed Circuit Assembler’s Guide to... Factory Analytics
04/24/2024 | I-Connect007 Editorial TeamIn our fast-changing, deeply competitive, and margin-tight industry, factory analytics can be the key to unlocking untapped improvements to guarantee a thriving business. On top of that, electronics manufacturers are facing a tremendous burden to do more with less. If you don't already have a copy of this book, what follows is an excerpt from the introduction chapter of 'The Printed Circuit Assembler’s Guide to... Factory Analytics: Unlocking Efficiency Through Data Insights' to whet your appetite.
Real Time with... IPC APEX EXPO 2024: Industrial Quality Solutions from Zeiss
04/23/2024 | Real Time with...IPC APEX EXPOEditor Nolan Johnson and Herminso Gomez of Zeiss Group discuss the company's industrial quality solutions, with a focus on X-ray technology. Zeiss provides a range of microscopy options and Herminso highlights the advantages of X-ray technology for aerospace, medical, and consumer electronics sectors.
Altair Acquires Cambridge Semantics, Powering Next-Generation Enterprise Data Fabrics and Generative AI
04/22/2024 | AltairAltair a global leader in computational intelligence, acquired Cambridge Semantics, a modern data fabric provider and creator of one of the industry’s leading analytical graph databases.
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
04/19/2024 | Marcy LaRont, PCB007 MagazineFor my must-read picks of the week, I’m highlighting Parker Capers, a young professional seeking employment, solid counsel from Dan Beaulieu on what your post-show plan should look like, more information and insight on “chiplets” and the need for secure data transfer standards from columnist Preeya Kuray, as well as Matt Stevenson’s design for reality wisdom. It’s a reminder to download one of our newest books (there are several) you don't want to miss if you are an assembler.