Optimizing Carbon Nanotube Electrodes
January 8, 2018 | MITEstimated reading time: 9 minutes
One widely used method for studying porous electrodes is electrochemical impedance spectroscopy (EIS). It involves pulsing voltage across electrodes in an electrochemical cell at a set time interval (frequency) while monitoring "impedance," a measure that depends on the available storage space and resistance to flow. Impedance measurements at different frequencies is called the "frequency response."
The classic model describing porous media uses that frequency response to calculate how much open space there is in a porous material. "So we should be able to use [the model] to calculate the space between the carbon nanotubes in a CNT electrode," Mutha says.
But there’s a problem: This model assumes that all pores are uniform, cylindrical voids. But that description doesn't fit electrodes made of CNTs. Mutha modified the model to more accurately define the pores in CNT materials as the void spaces surrounding solid pillars. While others have similarly altered the classic model, Mutha took her alterations a step further. The nanotubes in a CNT material are unlikely to be packed uniformly, so she added to her equations the ability to account for variations in the spacing between the nanotubes. With this modified model, Mutha could analyze EIS data from real samples to calculate CNT spacings.
Using the model
To demonstrate her approach, Mutha first fabricated a series of laboratory samples and then measured their frequency response. In collaboration with Yuan "Jenny" Lu '15, a materials science and engineering graduate, she deposited thin layers of aligned CNTs onto silicon wafers inside a furnace and then used water vapor to separate the CNTs from the silicon, producing free-standing forests of nanotubes. To vary the CNT spacing, she used a technique developed by MIT collaborators in the Department of Aeronautics and Astronautics, Professor Brian Wardle and postdoc associate Itai Stein PhD ’16. Using a custom plastic device, she mechanically squeezed her samples from four sides, thereby packing the nanotubes together more tightly and increasing the volume fraction — that is, the fraction of the total volume occupied by the solid CNTs.
To test the frequency response of the samples, she used a glass beaker containing three electrodes immersed in an electrolyte. One electrode is the CNT-coated sample, while the other two are used to monitor the voltage and to absorb and measure the current. Using that setup, she first measured the capacitance of each sample, meaning how much charge it could store in each square centimeter of surface area at a given constant voltage. She then ran EIS tests on the samples and analyzed results using her modified porous media model.
Results for the three volume fractions tested show the same trends. As the voltage pulses become less frequent, the curves initially rise at about a 45 degree slope. But at some point, each one shifts toward vertical, with resistance becoming constant and impedance continuing to rise.
As Mutha explains, those trends are typical of EIS analyses. "At high frequencies, the voltage changes so quickly that — because of resistance in the CNT forest — it doesn’t penetrate the depth of the entire electrode material, so the response comes only from the surface or partway in," she says. "But eventually the frequency is low enough that there’s time between pulses for the voltage to penetrate and for the whole sample to respond."
Resistance is no longer a noticeable factor, so the line becomes vertical, with the capacitance component causing impedance to rise as more charged particles attach to the CNTs. That switch to vertical occurs earlier with the lower-volume-fraction samples. In sparser forests, the spaces are larger, so the resistance is lower.
The most striking feature of Mutha's results is the gradual transition from the high-frequency to the low-frequency regime. Calculations from a model based on uniform spacing — the usual assumption — show a sharp transition from partial to complete electrode response. Because Mutha's model incorporates subtle variations in spacing, the transition is gradual rather than abrupt. Her experimental measurements and model results both exhibit that behavior, suggesting that the modified model is more accurate.
By combining their impedance spectroscopy results with their model, the MIT researchers inferred the CNT interspacing in their samples. Since the forest packing geometry is unknown, they performed the analyses based on three- and six-pillar configurations to establish upper and lower bounds. Their calculations showed that spacing can range from 100 nanometers in sparse forests to below 10 nanometers in densely packed forests.
Comparing approaches
Work in collaboration with Wardle and Stein has validated the two groups' differing approaches to determining CNT morphology. In their studies, Wardle and Stein use an approach similar to Monte Carlo modeling, which is a statistical technique that involves simulating the behavior of an uncertain system thousands of times under varying assumptions to produce a range of plausible outcomes, some more likely than others. For this application, they assumed a random distribution of "seeds" for carbon nanotubes, simulated their growth, and then calculated characteristics, such as inter-CNT spacing with an associated variability. Along with other factors, they assigned some degree of waviness to the individual CNTs to test the impact on the calculated spacing.
To compare their approaches, the two MIT teams performed parallel analyses that determined average spacing at increasing volume fractions. The trends they exhibited matched well, with spacing decreasing as volume fraction increases. However, at a volume fraction of about 26 percent, the EIS spacing estimates suddenly go up — an outcome that Mutha believes may reflect packing irregularities caused by buckling of the CNTs as she was densifying them.
To investigate the role played by waviness, Mutha compared the variabilities in her results with those in Stein's results from simulations assuming different degrees of waviness. At high volume fractions, the EIS variabilities were closest to those from the simulations assuming little or no waviness. But at low volume fractions, the closest match came from simulations assuming high waviness.
Based on those findings, Mutha concludes that waviness should be considered when performing EIS analyses — at least in some cases. "To accurately predict the performance of devices with sparse CNT electrodes, we may need to model the electrode as having a broad distribution of interspacings due to the waviness of the CNTs," she says. "At higher volume fractions, waviness effects may be negligible, and the system can be modeled as simple pillars."
The researchers' nondestructive yet quantitative technique provides device designers with a valuable new tool for optimizing the morphology of porous electrodes for a wide range of applications. Already, Mutha and Wang have been using it to predict the performance of supercapacitors and desalination systems. Recent work has focused on designing a high-performance, portable device for the rapid desalination of brackish water. Results to date show that using their approach to optimize the design of CNT electrodes and the overall device simultaneously can as much as double the salt adsorption capacity of the system, while speeding up the rate at which clean water is produced.
This research was supported in part by the MIT Energy Initiative Seed Fund Program and by the King Fahd University of Petroleum and Minerals (KFUPM) in Dhahran, Saudi Arabia, through the Center for Clean Water and Clean Energy at MIT and KFUPM. Mutha's work was supported by a National Science Foundation Graduate Research Fellowship and Stein's work by the Department of Defense through the National Defense Science and Engineering Graduate Fellowship Program.
Page 2 of 2Suggested Items
Keysight Enabling University of Stuttgart to Advance 6G Integrated Circuits Research
08/10/2023 | Keysight Technologies, Inc.Keysight Technologies, Inc. is enabling the University of Stuttgart to conduct foundational research essential to development of new integrated circuits (IC) for 6G technology with the new Keysight 6G Vector Component Analysis (VCA) solution.
KSG Group Puts Horizontal OSP Line for Organic Surfaces into Operation
07/31/2023 | KSG GroupThe KSG Group has expanded its capacities in the field of organic surface coating by bringing a new wet-chemical horizontal system online.
Mil/Aero Design: Not Just Another High-Rel Board
07/25/2023 | Andy Shaughnessy, Design007 MagazineMeijing Liu, CID+, is a senior PCB designer for Microart Services, an EMS company in Markham, Ontario, Canada. She recently took a six-week military/aerospace PCB design class from IPC’s Kris Moyer, and she was surprised at how much content she was able to absorb in such a short time. I spoke with Meijing and we discussed some of her takeaways from the class, and how it has inspired her to pursue more design education in the future.
MACOM Awarded U.S. Air Force Contract for Advanced Semiconductor Development
07/20/2023 | Business WireMACOM Technology Solutions Inc., a leading supplier of semiconductor products, announced that it has been awarded a contract from the United States Air Force Research Laboratory (“AFRL”) to develop advanced semiconductor process technology related to Gallium Nitride-on-Silicon Carbide (“GaN-on-SiC”).
Standard of Excellence: Today’s Hottest Technology Trends
07/21/2023 | Anaya Vardya -- Column: Standard of ExcellenceNo matter what anyone says, printed circuit boards are the backbone of modern electronics. Without the PCB, what will the components attach to? Without advancements in printed circuit board technology, products of the future would be impossible. It is our responsibility to be there when our customers need us—today and in the future. That means recognizing the latest trends and making the most of them. Here's what I see is trending in microelectronics.