-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Cadence Presents New Software System and Technical Papers at PCB West 2018
November 6, 2018 | Nolan Johnson, PCB007Estimated reading time: 12 minutes
Shah: There are two parts to that. One is getting the rules and design to them, which is important. The second part is that our DesignTrue DFM technology checks those rules in real time. This is a unique capability that we have. Earlier is always better. As soon as you make a mistake, it's cheaper to fix it as soon as you make it in design than if you finish the board and figure out what's wrong, and then move everything out.
One typical case is annular ring violations. As soon as you place a component, our tool will tell you that you have an annular ring violation. You don't want to place all of your components and put all the traces around it to find out late in the cycle that there are violations and you must move everything out of the way.
Johnson: It's an expensive rip up.
Shah: Exactly. Coupling the rules with this technology is what enables the designers and manufacturers to get the product out faster. It's a shorter design cycle for designers, and it's a very efficient process for manufacturers because that's where they want to go instead of doing the technical qualifiers (TQs) iterations with the customer.
Johnson: How long does the acceptance process take and what's the typical development time?
Fernsebner: The longest time for the manufacturer is creating the rules themselves. The rules can be as sophisticated or as simple as the manufacturer wants them to be. Overall, the rule set is quite robust. We now support approximately 2,500 DFM rules. Some manufacturers are not going to use all 2,500 because that's pretty extensive. Others don't want to fill out every single area because they might feel very protected and that's part of their IP. The length of time depends on how thorough they want to be when filling out the rules. However, as soon as you're registered and approved, you immediately appear as a vendor for customers.
Johnson: Do you see this as a global manufacturer network or regional?
Fernsebner: The program's brand new, so there are a few U.S. participants. The ultimate goal is to provide international services, such as Würth Electronics. They’re approved and based in Germany.
Johnson: With the Ecosystem, you’re already giving manufacturers a heads-up that there's a design started with them in mind. At some point, does the quoting and pricing information become a natural thing included in the customer/vendor conversation?
Shah: Yes. I think that's a natural progression to enable that sort of collaboration between the design house and manufacturers. We are working with a couple of partner companies to allow that directly from the design. We're not to the point of announcing that yet, but that's where we're going.
Johnson: Certainly, a concept down the road.
Shah: Correct.
Fernsebner: There is a long-term roadmap for this platform, and we are in phase one. Like Hemant said, the DesignTrue DFM technology is unique to Cadence. We have the only tools that check DFM rules in real time as the PCB designer is laying out the board. Some might argue by saying, "You're doing DFM against the actual PCB design file and not the physical manufacturing artwork." The reality is if you look at the manufacturing support we're already receiving early the program, many fabrication providers see the benefits and realize that the number of cyclical back-and-forth interactions with the design house can be greatly reduced with this platform.
Johnson: How do you see this DFM solution interacting with parts libraries?
Shah: That’s an interesting question. Part libraries become relevant when design for assembly (DFA) is part of it. The challenge is getting the manufacturers' libraries because every manufacturer has a slightly different profile. The design house can check a 3D part, but it's an approximation to what you're going to see on the manufacturing floor. We ensure that the design is correct based on the libraries customers provide, but the manufacturer will have to do that check again to make sure it's accurate. We'll bring it very close, but without having a manufacturer's library also in the design process, that's not solvable.
Johnson: That makes sense. You guys are doing some cool stuff that’s long overdue.
Shah: Yes, it is.
Fernsebner: As I said earlier, you can design whatever you want with software, but can you actually build it? That's where they say the proof is in the pudding.
Johnson: Can you tell us about the three papers you’ve recently published?
Page 2 of 3
Suggested Items
iNEMI Names Grace O'Malley CTO
05/02/2024 | iNEMIThe Board of Directors of the International Electronics Manufacturing Initiative (iNEMI) has named Grace O'Malley Chief Technical Officer (CTO).
Intel Takes Next Step Toward Building Scalable Silicon-Based Quantum Processors
05/02/2024 | BUSINESS WIRENature published an Intel research paper, “Probing single electrons across 300-mm spin qubit wafers,” demonstrating state-of-the-art uniformity, fidelity and measurement statistics of spin qubits.
ZESTRON Academy Launches 2024 Advanced Packaging & Power Electronics Webinar Series
05/01/2024 | ZESTRONZESTRON, the leading global provider of high-precision cleaning products, services, and training solutions in the electronics manufacturing and semiconductor industries, proudly announces the launch of its highly anticipated webinar series on Advanced Packaging & Power Electronics, a webinar series on the latest innovations, cleaning, and corrosion challenges.
NextFlex Convenes the Hybrid Electronics Community at Binghamton University
05/01/2024 | NextFlexBinghamton University hosted the NextFlex hybrid electronics community on April 18 for a day of expert presentations, breakout sessions on technology and manufacturing topics, and networking.
HQ NextPCB of HQ Electronics Debut on the International Stage for Electronics Manufacture at IPC APEX 2024
05/01/2024 | PRNewswireHQ NextPCB of HQ Electronics, a leading Chinese-based multilayer PCB manufacturer and assembly house showcased its industrial prowess on the international stage for the first time at the IPC APEX Expo 2024.