Replaceable Solar Cell
September 23, 2019 | MITEstimated reading time: 5 minutes
Bulović hopes the study will “shift the paradigm of what has been accepted as a global truth.” Up to now, he says, “many promising technologies never even got a start, because the bar is set too high” on the need for durability.
For their analysis, the team looked at three different kinds of solar installations: a typical 6-kilowatt residential system, a 200-kilowatt commercial system, and a large 100-megawatt utility-scale system with solar tracking. They used NREL benchmark parameters for U.S. solar systems and a variety of assumptions about future progress in solar technology development, financing, and the disposal of the initial panels after replacement, including recycling of the used modules. The models were validated using four independent tools for calculating the levelized cost of electricity (LCOE), a standard metric for comparing the economic viability of different sources of electricity.
In all three installation types, they found, depending on the particulars of local conditions, replacement with new modules after 10 to 15 years could in many cases provide economic advantages while maintaining the many environmental and emissions-reduction benefits of solar power. The basic requirement for cost-competitiveness is that any new solar technology that is to be installed in the U.S should start with a module efficiency of at least 20 percent, a cost of no more than 30 cents per watt, and a lifetime of at least 10 years, with the potential to improve on all three.
Jean points out that the solar technologies that are considered standard today, mostly silicon-based but also thin-film variants such as cadmium telluride, “were not very stable in the early years. The reason they last 25 to 30 years today is that they have been developed for many decades.” The new analysis may now open the door for some of the promising newer technologies to be deployed at sufficient scale to build up similar levels of experience and improvement over time and to make an impact on climate change earlier than they could without module replacement, he says.
“This could enable us to launch ideas that would have died on the vine” because of the perception that greater longevity was essential, Bulović says.
The study was supported by the Tata-MIT GridEdge Solar research program.
Page 2 of 2Suggested Items
KIC’s Miles Moreau to Present Profiling Basics and Best Practices at SMTA Wisconsin Chapter PCBA Profile Workshop
01/25/2024 | KICKIC, a renowned pioneer in thermal process and temperature measurement solutions for electronics manufacturing, announces that Miles Moreau, General Manager, will be a featured speaker at the SMTA Wisconsin Chapter In-Person PCBA Profile Workshop.
The Drive Toward UHDI and Substrates
09/20/2023 | I-Connect007 Editorial TeamPanasonic’s Darren Hitchcock spoke with the I-Connect007 Editorial Team on the complexities of moving toward ultra HDI manufacturing. As we learn in this conversation, the number of shifting constraints relative to traditional PCB fabrication is quite large and can sometimes conflict with each other.
Standard Of Excellence: The Products of the Future
09/19/2023 | Anaya Vardya -- Column: Standard of ExcellenceIn my last column, I discussed cutting-edge innovations in printed circuit board technology, focusing on innovative trends in ultra HDI, embedded passives and components, green PCBs, and advanced substrate materials. This month, I’m following up with the products these new PCB technologies are destined for. Why do we need all these new technologies?
Experience ViTrox's State-of-the-Art Offerings at SMTA Guadalajara 2023 Presented by Sales Channel Partner—SMTo Engineering
09/18/2023 | ViTroxViTrox, which aims to be the world’s most trusted technology company, is excited to announce that our trusted Sales Channel Partner (SCP) in Mexico, SMTo Engineering, S.A. de C.V., will be participating in SMTA Guadalajara Expo & Tech Forum. They will be exhibiting in Booth #911 from the 25th to the 26th of October 2023, at the Expo Guadalajara in Jalisco, Mexico.
Intel Unveils Industry-Leading Glass Substrates to Meet Demand for More Powerful Compute
09/18/2023 | IntelIntel announced one of the industry’s first glass substrates for next-generation advanced packaging, planned for the latter part of this decade.