Researchers Create Cheaper High Performing LED
November 19, 2015 | Florida State UniversityEstimated reading time: 3 minutes
A team of Florida State University materials researchers has developed a new type of light-emitting diode, or LED, using an organic-inorganic hybrid that could lead to cheaper, brighter and mass produced lights and displays in the future.
Assistant Professor of Physics Hanwei Gao and Associate Professor of Chemical Engineering Biwu Ma are using a class of materials called organometal halide perovskites to build a highly functioning LED. They lay out their findings in the journal Advanced Materials.
“Early work suggested perovskites could be a promising material to build LEDs,” Gao said. “But, the performance was not up to their potential. We believed there was significant room for improvement.”
Perovskites are any materials with the same type of crystal structure as calcium titanium oxide. Other researchers experimented with perovskites to build LEDs in the past but could not build particularly effective ones. Gao and Ma believed this organic-inorganic hybrid could perform better, if the formula could be appropriately tweaked.
“When we thought about this class of material, we knew it should perform better than this,” Ma said. “We came up with our novel approach to solve some critical problems and get a high-performance LED.”
After months of experiments using synthetic chemistry to fine-tune the material properties and device engineering to control the device architectures, they ultimately created an LED that performed even better than expected.
The material glowed exceptionally bright.
It is measured at about 10,000 candelas per square meter at a driving voltage of 12V — candelas are the unit of measurement for luminescence. As a benchmark, LEDs glowing at about 400 candelas per square meter are sufficiently bright for computer screens.
“Such exceptional brightness is, to a large extent, owing to the inherent high luminescent efficiency of this surface-treated, highly crystalline nanomaterial,” Gao said.
It was also quick and easy to produce.
Gao and Ma can produce the material in about an hour in the lab and have a full device created and tested in about half a day.
Additionally, while bare hybrid perovskites tend to be unstable in humid air, the nanostructured perovskites exhibit remarkable stability in ambient environment because of the purposely designed surface chemistry. Such chemical stability largely reduces the requirement of sophisticated infrastructure to produce this new type of LEDs and could be of huge benefit for cost-effective manufacturing in the future.
The research is crucial to the advance of LED technology, which is fast becoming an avenue to reduce the country’s electric consumption. LED lighting is already sold in stores, but widespread adoption has been slow because of the costs associated with the material and the quality.
Page 1 of 2
Suggested Items
Material Insight: The Dielectric Constant of PCB Materials
05/17/2024 | Dr. Preeya Kuray -- Column: Material InsightIn the world of PCB design, miniaturization can be achieved by using low dielectric constant (Dk) materials. Low Dk materials can allow for a reduction in thickness while maintaining a given trace width, leading to lower transmission loss and higher density circuitry.
IPC APEX EXPO: Some Thoughts About Growth
05/16/2024 | Dan Feinberg, I-Connect007After two and a half days of wandering the aisles at IPC APEX EXPO 2024, for the first time, I almost felt like I was exploring CES. There were so many booths and exhibits that I could describe, but I’d like to focus on the growth and huge value of this event, which has expanded well beyond just the growing and impressive exhibit show floor.
The Shaughnessy Report: Unlock Your High-speed Material Constraints
05/15/2024 | Andy Shaughnessy -- Column: The Shaughnessy ReportThe world of PCB materials used to be a fairly simple one. It was divided into two groups: the “traditional” laminates, often called FR-4, and the high-speed laminates developed especially for high-speed PCBs. These were two worlds that usually didn’t collide. But then traditional laminates started getting better, and high-speed designers and design engineers took notice and started to reconsider what FR-4 could be used for.
Breaking High-speed Material Constraints: Design007 Magazine — May 2024
05/14/2024 | I-Connect007 Editorial TeamDo you need specialty materials for your high-speed designs? Maybe not. Improvements in resins mean designers of high-speed boards can sometimes use traditional laminate systems instead of high-speed materials, saving time and money while streamlining the fab process. In the May 2024 issue of Design007 Magazine, our contributors explain how to avoid overconstraining your materials when working with high-speed boards.
Indium Experts to Present at Electronics in Harsh Environments SMTA Conference
05/13/2024 | Indium Corporationndium Corporation Technical Manager for Europe, Africa, and the Middle East, Karthik Vijay, will deliver a technical presentation and Indium Corporation Senior Technologist, Dr. Ronald Lasky, will deliver both a workshop and technical presentation at the Electronics in Harsh Environments SMTA Conference on May 14-16 in Copenhagen, Denmark.