Mass Produced 3D Printed Electronics
December 10, 2015 | IDTechExEstimated reading time: 4 minutes
Ten short years ago 3D printing was almost the exclusive remit of rapid prototyping. Nobody was putting 3D printing into mass production back then. Fast forward one decade and the world leader in jet engines, GE, are 3D printing over 100,000 fuel nozzles for their next-generation LEAP gas turbines that could be flying around in commercial aircraft as early as 2016. Perhaps more surprising is that 3D printed electronics, a subject barely heard of more than a year ago, is now also being put into mass production as market leader Optomec have installed machines in China to manufacture 15 million antennas for mobile devices every year. Leveraging the benefits of 3D printing requires next generation design software, the kind of software pioneered by startup WITHIN Technologies who were acquired by Autodesk last year for $88m. GE and Autodesk made a strategic investment in Optomec last week. This is partly to sustain Optomec's incredible 80% revenue growth but also marks the beginning of a deeper collaboration between the three companies. A collaboration that will have far-reaching consequences.
GE already have seven of Optomec's machines spread across their divisions. Autodesk are an existing supplier of software for Optomec's machines. The collaboration between these companies will see them develop easier-to-use solutions employing open and machine-agnostic interoperability with other software and machines. In other words, their work is for the benefit of everyone and will impact a wide range of industries. The design software will be made aware of the target machine and, in particular, its capabilities and limitations. In contrast to current fragmented solutions with separate CAD and CAM packages, this fusing of the separate software components will allow the design software to take full advantage of the target machine in two interesting ways. Firstly, failures can be moved from the print phase up to the design phase, picking them up much earlier in the development cycle and saving precious time and money. Secondly, the availability of printer-specific information at design time will allow computational (aka declarative) designs to be optimised for the specific target machine. As we have mentioned in a previous article, the availability of easy-to-use declarative design software will precipitate a paradigm shift in the way almost every 3D printed part is designed. Finally, certification of 3D printed materials remains a huge unsolved problem for many industries, most notably aerospace. This collaboration also intends to address the certification of 3D printed parts and materials using this integrated solution.
The technologies being developed by Optomec, GE and Autodesk play straight into the huge emerging markets for industrial IoT and wearable technologies as well as healthcare. The major business motivation for industrial IoT is condition-based maintenance, i.e. smart parts that convey whether or not they are in need of repair. For example, the life span of a $1k part can be extended by 25-100% by adding a $1 sensor. Optomec have printed sensors on wearable devices such as strain sensors in eyewear that can detect you flexing your ears. They have also done smart watches and are serious about 3D printed electronics on contact lenses which they say will be commercially available in the next few years. In healthcare, Optomec have 3D printed sensors on catheters that allow a patient to be monitored internally during surgical procedures. A major MRI machine manufacturer contacted us and asked if it was possible to 3D print the housing of an MRI machine with integrated conductive traces to replace conventional wiring that is, apparently, a "nightmare".
Page 1 of 2
Suggested Items
Altair Acquires Research in Flight, Forging a New Path for Aerodynamic Analysis
05/07/2024 | AltairAltair a global leader in computational intelligence, announced it has acquired Research in Flight, maker of FlightStream®, which provides computational fluid dynamics (CFD) software with a large footprint in the aerospace and defense sector and a growing presence in marine, energy, turbomachinery, and automotive applications.
Altair Acquires Research in Flight, Forging a New Path for Aerodynamic Analysis
05/03/2024 | AltairAltair a global leader in computational intelligence, announced it has acquired Research in Flight, maker of FlightStream®, which provides computational fluid dynamics (CFD) software with a large footprint in the aerospace and defense sector and a growing presence in marine, energy, turbomachinery, and automotive applications.
Boeing, GKN Aerospace Close Deal for St. Louis Site
04/29/2024 | BoeingBoeing has closed a deal with GKN Aerospace St. Louis and its parent company, Melrose Industries, to continue the manufacturing of critical components that support the U.S. government and its allies.
Cicor Records Solid Growth in Q1
04/16/2024 | CicorThe Cicor Group continued to grow in the first three months of the year. Quarterly sales increased by 11.8% to CHF 107.3 million compared to the first quarter of the previous year (Q1/2023: CHF 96.0 million).
TT Electronics Awarded Contract with Kongsberg Defence and Aerospace
04/11/2024 | TT ElectronicsTT Electronics, a leading provider of global manufacturing solutions and engineered technologies, announced today that its Fairford UK business has been awarded a new contract with long-standing customer Kongsberg Defence and Aerospace (Kongsberg) for the production of complex cable harness solutions.