Precision Measurements for Magnetic Memory
May 3, 2016 | DTUEstimated reading time: 2 minutes
MRAM is a memory type that combines the advantageous characteristics of three important memory solutions used in consumer electronics. This includes the high density of DRAM (dynamic RAM), the high speed of SRAM (static RAM) and the nonvolatile (i.e. the ability to retrieve stored information even after having been turned off and back on) storage of Flash memory.
The active part of an MRAM cell is a so called magnetic tunnel junction which uses the magnetic properties of electrons, i.e. the electron spin, to read and write magnetic information in the memory cell. The most critical part in such a magnetic tunnel junction is the electron transport properties across a dielectric layer, e.g. magnesium oxide, with a thickness of just 1 nm (a few atomic layers). Through the past decade these properties have been characterised using a measurement system developed by the DTU Nanotech spin-off company Capres A/S.
Towards a large scale production of MRAM
To produce a well-functioning memory device with hundreds of millions of MRAM cells, it is necessary to monitor precisely the electrical properties and as MRAM enters into large scale production, the requirements on metrology increase significantly. Measurement speed, precision and reliability must be improved compared to previous generations of metrology systems. Also, measurements must be possible on test structures available in production that may differ from test samples in product development. These issues have been addressed in a number of collaboration projects between Capres A/S and DTU Nanotech.
Senior Researcher Dirch Hjorth Petersen explains: “By detailed analysis of the metrology system, we have identified the most critical parameters and optimised the measurement routines accordingly. With this, we have been able to reduce measurement time by a factor of 5 and we have developed a methodology for a product specific measurement procedure”.
The customised procedure yields significant improvements in measurement precision as compared to previous state-of-the-art measurements. The measurement reliability is being improved through use of vibration tolerant electrodes for superior measurement stability, and early tests are encouraging. Finally, a model has been developed to allow measurements in small test pads relevant for production monitoring.
Co-founder and CTO at Capres A/S, Peter Folmer Nielsen states: “We expect the combination of improvements to pave the road for fully automated monitoring of product quality during MRAM production”.
The improvements have been achieved through collaboration between Industrial Postdocs Alberto Cagliani and Frederik W. Østerberg, former Industrial PhD student Daniel Kjær, as well as Senior Researcher Dirch H. Petersen and Professor Ole Hansen.
Suggested Items
The Right Approach: I Hear the Train A Comin'
04/25/2024 | Steve Williams -- Column: The Right ApproachTraining is often an afterthought in many organizations, and the longer a company has been in business, the more this seems to apply. Over the past couple of decades, it has been amazing to observe that the biggest offenders of this are the companies that overuse the sound bite, “Our most important assets are our people.” When you dig into the process and peel back the onion, their commitment to training is not commensurate with that statement.
Big Win for Defense Production Act Budget Allocation in FY24 Budget
04/23/2024 | I-Connect007 Editorial TeamOne year ago, President Biden issued a determination that chips and packaging are critical for national security. Since that time, much work has been done to continue the conversation in Washington, elevating the importance of the entire chips value chain, and including printed circuit boards and substrates, without which chips cannot operate.
IDTechEx Examines the Opportunities for Wearables in Digital Health
04/19/2024 | IDTechExIDTechEx’s report, “Digital Health and Artificial Intelligence 2024-2034: Trends, Opportunities, and Outlook”, covers this ongoing trend in the consumer health wearables market and includes analysis of the opportunities and roadmap for biometric monitoring.
NCAB Appoints Tim Benjamin as New CFO
04/15/2024 | NCAB GroupNCAB Group has appointed Tim Benjamin as its new CFO. Tim has a long and broad experience of managerial business finance roles, including M&A and IT.
Plastronics and the New IPC Guidelines for In-mold Electronics (IME)
04/11/2024 | Barry Matties, I-Connect007In the ever-evolving world of electronics, the roads for the integration of electronics assemblies into 3D structures continue to grow into a set of technologies used to produce 3D plastronics parts and revolutionize mainly the automotive industry. IPC has been developing standards for this set of technologies, led by Francisco Fourcade, IPC electronics technology standards manager.