Manufacturing Productivity Growth Slows to Crawl Worldwide
July 15, 2016 | The Conference BoardEstimated reading time: 3 minutes
Productivity in manufacturing continues to stagnate in economies around the globe, according to new data from the International Labor Comparisons (ILC) program of The Conference Board. Nearly two-thirds of the mostly advanced economies covered in the dataset saw manufacturing productivity growth slow between 2014 and 2015. More than half registered growth of less than 1% in 2015 and six countries even posted negative productivity growth last year.
“The manufacturing picture mirrors our generally anemic global productivity outlook,” said Bart van Ark, global chief economist at The Conference Board. “While manufacturing labor productivity actually grew faster in 2015 than overall productivity in two-thirds of the countries included in the ILC data, the dismal year-over-year trends suggest manufacturing can hardly be considered a bright spot. As manufacturing is an important engine of innovation, these miniscule growth rates are indicative of the enormity of the growth challenge facing mature economies.”
In the United States, manufacturing productivity improved marginally—from no growth in 2014 to 0.4% growth in 2015—while the Euro Area as a whole saw slightly stronger acceleration to 1.7% growth in 2015, up from 1.1% the previous year, reinforcing the cyclical recovery in many European economies. In contrast, Australia showed the sharpest decline in productivity growth (−3.5%) mainly due to a collapse in commodities trade.
“The rapid appreciation of the U.S. dollar has been the one silver lining and savior for global manufacturers based in Europe and the Asia-Pacific region,” said Elizabeth Crofoot, senior economist with the ILC program. “In 2015, even economies with stagnant or declining labor productivity increased their competitive edge against U.S. manufacturing, as measured by dollar-denominated unit labor cost (ULC). In the United States itself, however, the strengthening dollar is compounding the impact of weak productivity growth to seriously undermine the competitive standing of American manufacturing.”
In dollar terms, unit labor costs in the U.S. rose 2.2% in 2015. Taiwan (+0.1%) was the only other economy that saw ULC rise. By contrast, the appreciation of the dollar against the euro and other currencies produced major labor cost savings—and increased competitiveness versus the U.S.—throughout continental Europe, ranging from Germany’s −15.3% decline in ULC to Norway’s −19.4%. Even nations that saw negative productivity growth in 2015 experienced double-digit declines in relative labor costs thanks to depreciations of the local currency, including Canada (−10.8% ULC growth), Japan (−12.3%), and Australia (−13.6%).
Other key developments in manufacturing productivity from International Labor Comparisons:
- Gloomy U.K. picture could be darkened further by Brexit. British manufacturing productivity decelerated substantially from 3.4 percent growth in 2014 to no growth in 2015. While ULC declined 2.4 percent in dollar terms, U.K. manufacturing competitiveness deteriorated relative to all other countries except the U.S., Taiwan, Singapore, and South Korea. With nearly half of U.K. manufacturing exports destined for the rest of the E.U., boosting productivity will be crucial to staying competitive in the face of uncertainty over future trade terms and currency values. This will depend on maintaining the flow of skilled immigrants—which may well be politically untenable given the E.U. referendum result.
- A combination of declining output and increased hours worked reeled Japanese manufacturing productivity into negative territory at −1.8% growth in 2015, down from 1.2% in 2015. Elsewhere in Asia, Singapore (−1.6%) and South Korea (−0.4%) also saw productivity growth turn negative.
- Manufacturing productivity growth in Germany remains below 1.0%, falling slightly to 0.7% in 2015. France, by contrast, saw a substantial improvement to 3.5% growth in 2015—from 0.6% a year earlier—as a result of rising output coupled with a decline in hours worked.
- Ireland saw by far the strongest productivity growth, at 12.7% in 2015. This doubles the 2014 rate, which was already the highest in the ILC cohort. Combined with the euro’s depreciation against the dollar, unit labor costs declined 24.9%, dramatically boosting Irish manufacturing’s global competitiveness.
About the Conference Board
The Conference Board is a global, independent business membershipand research association working in the public interest. Our mission is unique: To provide the world’s leading organizationswith the practical knowledge they need to improve their performance and better serve society. The Conference Board is a non-advocacy, not-for-profit entity holding 501 (c) (3) tax-exempt status in the United States.
Suggested Items
Latest Test and Inspection Solutions from GOEPEL electronic at SMTconnect 2024
04/29/2024 | GOEPEL electronicGOEPEL electronic will be demonstrating automated test and inspection equipment at SMTconnect, taking place in Nuremberg from June 11 to 13, 2024.
SIA Commends CHIPS Act Incentives for Micron’s Manufacturing Projects in New York and Idaho
04/29/2024 | SIAThe Semiconductor Industry Association (SIA) today released the following statement from SIA President and CEO John Neuffer applauding semiconductor manufacturing incentives announced by the U.S. Department of Commerce and Micron.
Real Time with… IPC APEX EXPO 2024: Tools, Training, and Trends in Manufacturing Engineering
04/25/2024 | Real Time with...IPC APEX EXPOGuest Editor Kelly Dack and Product Specialist Erik Bateham of Polar Instruments discuss Polar's latest technology, including their role in aiding manufacturing engineers. They highlight the advanced capabilities of Polar's tools and the critical role of signal integrity analysis, as well as the importance of accurate modeling in board manufacturing. Polar's unique training approach and demonstration contact details are also explored.
TTM Celebrates the Grand Opening of Its First Manufacturing Facility in Penang
04/25/2024 | TTM Technologies, Inc.TTM Technologies, Inc., a leading global manufacturer of technology solutions including mission systems, radio frequency (RF) components and RF microwave/microelectronic assemblies, and quick-turn and technologically advanced printed circuit boards (PCBs), officially opened its first manufacturing plant in Penang, Malaysia with an investment of USD200 million (approximately RM958 million).
Listen Up! The Intricacies of PCB Drilling Detailed in New Podcast Episode
04/25/2024 | I-Connect007In episode 5 of the podcast series, On the Line With: Designing for Reality, Nolan Johnson and Matt Stevenson continue down the manufacturing process, this time focusing on the post-lamination drilling process for PCBs. Matt and Nolan delve into the intricacies of the PCB drilling process, highlighting the importance of hole quality, drill parameters, and design optimization to ensure smooth manufacturing. The conversation covers topics such as drill bit sizes, aspect ratios, vias, challenges in drilling, and ways to enhance efficiency in the drilling department.