Public Safety Increased With the Ability to Remotely Disable Vehicles
August 1, 2016 | CORDISEstimated reading time: 3 minutes
In its endeavour to keep the public safe, one of the key challenges facing European security services is the ability to control and stop, at distance, non-cooperative vehicles posing a threat. However, this ability presents more than a technical challenge. To comply with EU legislation, as well as adhere to ethical concerns, the technology would also have to be safe for the user, the driver (and passengers), as well as members of the public and the material infrastructure of the surrounding environment.
The SAVELEC (Safe control of non cooperative vehicles through electromagnetic means) project developed a prototype device, after testing signals (magnetic pulses and microwave), which interfered with key car components, forcing it to slow down and stop. With the contribution of security forces as the ultimate end users, the researchers were able to simulate the technology’s use in realistic scenarios.
Prototype device for a variety of security scenarios
SAVELEC first set up an end-user advisory panel comprising of law enforcement agencies and associated security organisations from different European countries, to better understand the likely operating environment for any technology developed. Scenarios were identified in terms of operational distance, target speed, distance to nearby persons and any immediate environmental considerations. As the project’s coordinator, Dr. Marta Martínez Vázquez points out, ‘This analysis included land and maritime missions, with the device implemented on a ground, seaborne or airborne platform.’
Developing the technology itself first required a review and cost analysis of what was currently available on the market, as well as establishing the car components best targeted for remote interference. In lab bench testing SAVELEC evaluated signal frequency, waveform and duration - principally of electromagnetic pulses (EMP) and high power microwaves (HPM) - to determine which could best disrupt the functioning of a vehicle’s electronic components.
Assessing the project’s success, Dr. Martínez Vázquez asserts that, ‘An EMP/HPM car-stopping device prototype at a breadboard level was designed, fabricated and tested. Its performance was successfully demonstrated in an open field controlled track, in of the presence of SAVELEC affiliated end-users’. The capacity of the prototype also surpassed expectations. ‘It demonstrated the functionality of the whole device, with a car moving on an open air track,’ she comments. ‘Conservative expectations had been to only demonstrate a sub-system of the device, or the whole system, but with a stationary car.’
The project also used the simulated environment to investigate the wider impact of the technology on humans and materials. For example, it looked at driver reactions to loss of vehicle control under six different scenarios including high speed, dense traffic and narrow roads, involving over 70 volunteers. A literature review of previous results allowed the assessment of the likelihood of petrol tank explosions from electromagnetic exposure or damage to airbags. Additionally, it assessed three different electromagnetic exposure scenarios for the pedestrian/bystander, car driver and device operator to ascertain safety limits.
Beyond proof-of-concept
A core outcome of the project, with the help of the European security forces and an Independent Ethics Advisory Board, was a regulatory framework proposal within which this technology could function. The framework included compatibility with European legislation which ensures the safety of all those exposed to electromagnetism.
For the prototype device to progress beyond the successful proof-of-concept stage, there are two principal challenges which would have to be overcome. ‘Further investigation should concentrate on the miniaturisation of the different components, and in extending its operational range (by increasing the power that can be generated),’ Dr. Martínez Vázquez says. She also recommends that different car models should be tested, as SAVELEC concentrated on only one. There should also be further investigation on human health and safety implications.
Whilst SAVELEC specifically tested the technology on cars, it could easily be adapted to other vehicles such as fast vessels, trucks or motorbikes. The project’s results have also contributed to improvements in other fields, such as the study of human exposure to electromagnetic fields and the development of better driving simulators.
Suggested Items
Samsung Electronics Begins Industry’s First Mass Production of 9th-Gen V-NAND
04/29/2024 | Samsung ElectronicsSamsung Electronics, the world leader in advanced memory technology, today announced that it has begun mass production for its one-terabit (Tb) triple-level cell (TLC) 9th-generation vertical NAND (V-NAND), solidifying its leadership in the NAND flash market.
TSMC Celebrates 30th North America Technology Symposium
04/29/2024 | TSMCTSMC unveiled its newest semiconductor process, advanced packaging, and 3D IC technologies for powering the next generation of AI innovations with silicon leadership at the Company’s 2024 North America Technology Symposium.
QinetiQ Achieves UK’s First Jet-to-Jet Teaming Between Aircraft and Autonomous Drone
04/29/2024 | QinetiQQinetiQ has successfully trialled the UK’s first Crewed-Uncrewed-Teaming demonstration between a crewed aircraft and an autonomous jet drone.
Warm Windows and Streamlined Skin Patches – IDTechEx Explores Flexible and Printed Electronics
04/26/2024 | IDTechExFlexible and printed electronics can be integrated into cars and homes to create modern aesthetics that are beneficial and easy to use. From luminous car controls to food labels that communicate the quality of food, the uses of this technology are endless and can upgrade many areas of everyday life.
iNEMI Packaging Tech Topic Series: Role of EDA in Advanced Semiconductor Packaging
04/26/2024 | iNEMIAdvanced semiconductor packaging with heterogenous integration has made on-package integration of multiple chips a crucial part of finding alternatives to transistor scaling. Historically, EDA tools for front-end and back-end design have evolved separately; however, design complexity and the increased number of die-to-die or die-to-substrate interconnections has led to the need for EDA tools that can support integration of overall design planning, implementation, and system analysis in a single cockpit.