Plug In for Renewable Energy
December 22, 2016 | Michigan State UniversityEstimated reading time: 3 minutes
A new study shows a huge US market for plug and play solar energy, with billions of dollars in retail sales and energy savings. So what's holding up widespread use?
Support for solar energy is vast. According to a 2015 Gallup poll, 79 percent of Americans want the US to put more emphasis on developing solar power. Most of the same people, unfortunately, can’t afford to install solar energy systems in their homes. Even after federal tax credits, installing solar panels to cover all of a family's electricity needs can cost tens of thousands of dollars. For others, a home solar system isn’t a consideration because they rent, or move frequently.
But Michigan Technological University’s Joshua Pearce says he knows the solution: plug and play solar.
“Plug and play systems are affordable, easy to install, and portable,” says Pearce, an associate professor of materials science and engineering and of electrical and computer engineering. “The average American consumer can buy and install them with no training.”
In a study funded by the Conway Fellowship and published in Renewable Energy (DOI: 10.1016/j.renene.2016.11.034), Pearce and researchers Aishwarya Mundada and Emily Prehoda estimate that plug and play solar could provide 57 gigawatts of renewable energy – enough to power the cities of New York and Detroit – with potentially $14.3 to $71.7 billion in sales for retailers and $13 billion a year in cost savings for energy users.
Sounds great, right? Well, there’s one problem: in many parts of the United States, electrical regulations don’t allow consumers to plug and play.
Small Investment, Big Return
Plug and play solar panels connect to an ordinary electrical outlet. You’re still on the grid, but you’ve become a “prosumer” — a consumer of energy who also produces it. The panels range in wattage and are relatively affordable, with some costing just a couple hundred dollars apiece. A prosumer can start small, with just one panel, and slowly build up over time to a system that produces 1 kilowatt of energy, the equivalent of powering 10 100-watt LED light bulbs.
The panels are also portable. So, for example, if a college student buys one 250-watt plug and play panel each year for four years, reaching 1 kilowatt of energy by senior year, that student can unplug the four panels when she graduates and take them to her next destination.
Pearce estimates that plug and play systems could generate more than four times the amount of electricity generated from all of US solar last year.
“The vast majority of this energy never leaves the home,” Pearce says. “It’s the equivalent of handling a hair dryer load. We’re talking about almost nothing on the electrical grid – but that nothing adds up. It’s an appliance with a high rate of return.”
Safe, Simple — And Largely Prohibited
In the United States, a patchwork of local jurisdictions and regulations make it difficult to figure out if and where plug and play panels are allowed.
“You can buy the panels,” Pearce says, “but you might not be able to plug them in, depending on your utility.”
In a paper published earlier this year in Solar Energy (DOI: 10.1016/j.solener.2016.06.002), Pearce, Mundada and researcher Yuenyong Nilsiam reviewed all regulations in the US that would apply to plug and play systems. They found no safety or technical issues with the equipment on the market.
“This is an area where less regulation could really help renewable energy,” Pearce says. “We know that the technology is safe, and the law should reflect that.”
The risk, according to Pearce, is putting too much current on one circuit, so he recommends that homeowners keep their plug and play systems to a kilowatt or less. Simple precautions make this easy — if a panel is plugged into an outdoor outlet, for example, safety plugs on all other outdoor outlets on that circuit can prevent overload.
While some jurisdictions have recognized that there are no major safety or technical issues with plug and play panels, paperwork holds up the process. Potential prosumers often have to fill out complicated forms to fulfill utility requirements, and the paperwork and associated fees vary by utility. To simplify the process, Pearce and colleagues automated it, by writing open-source computer code that fills out every possible technical requirement. Utilities can easily use the free code on their websites.
“Some utilities have embraced plug and play, and some have ignored it because they think it’s a pittance,” Pearce says. “But plug and play solar is something that can help most Americans.”
Suggested Items
Camtek Receives Approx. $25M from tier-1 manufacturer for High Bandwidth Memory (HBM)
03/29/2024 | CamtekCamtek Ltd. announced that it has received a new order for approximately $25 million from a tier-1 HBM manufacturer, for the inspection and metrology of High Bandwidth Memory (HBM). Most of the systems are expected to be delivered in the second half of 2024.
Reducing Nitrogen Consumption in Convection Soldering with Rehm Thermal Systems' Patented Mechatronic Curtain
03/28/2024 | Rehm Thermal SystemsCurrent developments indicate a need for larger throughput heights due to the trend towards e-mobility, which in turn increases nitrogen consumption for process inertization. Rehm Thermal Systems responds to this issue with an innovative solution: the mechatronic curtain.
CentraTEQ to Showcase Wide Range of Vibration & Environmental Test Systems at Battery Tech Expo 24
03/26/2024 | CentraTEQEnvironmental and vibration test specialists CentraTEQ are excited to be exhibiting at the upcoming Battery Tech Expo, scheduled to take place at Silverstone on April 25, 2024.
SEMI 3D & Systems Summit To Spotlight Trends In Hybrid Bonding, Chiplet Design And Environmental Sustainability
03/26/2024 | SEMILeading experts in 3D integration and systems for semiconductor manufacturing applications will gather at the annual SEMI 3D & Systems Summit, 12-14 June, 2024,
iNEMI/IPC White Paper on Complex Integrated Systems Highlights Future Technology and Manufacturing Ecosystem Needs
03/25/2024 | IPCToday’s system solutions combine more varied functionality, such as digital, analog, optical, micro-mechanical, etc., packed into smaller form factors. As a result, electronics manufacturing has to deliver increasingly complex integration of diverse technologies with system designs that blur the distinction between chip, package, board, and assembly.