Nanoscale Modifications can be used to Engineer Electrical Contacts for Nanodevices
January 16, 2017 | Swansea UniversityEstimated reading time: 4 minutes
Scientists at Swansea University show nanoscale modifications to the edge region of nanocontacts to nanowires can be used to engineer the electrical transport process.
Figure 1. Schematic diagram showing the electrical measurements performed on nanowires that have different sized Au particles (left) and the resultant current-voltage behaviour (centre) is controlled by geometrical effects that determine the magnitude of tunnelling current at the contact edge, shown by finite-element simulations (right). This effect is the basis for engineering the electrical contacts. Taken from open access reference 1. Image: Alex Lord/Swansea University.
With the emergence of 1-d and 2-d nanostructures as the future of electronic materials there is a pressing need to develop new electrical contact preparation techniques that can refine the traditional processes for nanotechnological devices. The future of semiconductor devices brings significant challenges as the dimensions of the device components have been reduced from 3-d to 2-d, and now to 1-d. This research team, led by Prof. Wilks at Swansea University, is pursuing methods to engineer quantum based electrical contact technology to address the needs of the semiconductor industry as it develops devices based on nanomaterials.
Electrical contacts are essential components for any electrical device as they control the flow of electrical charge into and out of the device. When a lack of control over the final contact properties is present designing and optimising the system is impossible. Through decades of experimental and theoretical study a degree of control has been developed through band engineering when selecting contacts to large-scale planar devices such as field effect transistors. Before the advent of nanotechnology, semiconductor devices applied thin material layers to engineer interfaces and contacts, such as lasers using quantum wells, in which case the active layers could be considered 2-dimensional in nature. Now with the intense study of nanotubes, nanowires, nanorods, quantum wires, nanoribbons and many other materials the physics in some cases has been reduced to one dimension.
The current research project was expressed by Dr. Alex Lord, “New technologies based on these materials are emerging such as chemical and biological sensors, quantum computing, energy harvesting, lasers, and environmental- and photon-detectors. However, reliably engineering electrical contacts to these nanomaterials is essential to allow the development of nanoscience into a real-world technology and bring about the profound advances to the electronics industry that Scientists and Engineers know are possible.” The researcher notes that “traditional methods of engineering electrical contacts have been applied to nanomaterials but often neglect the nanoscale effects that nanoscientists have worked so hard to uncover. At the current time, a design toolbox to fabricate electrical contacts of chosen properties to nanomaterials is not close and research is lagging behind our potential application of the materials.”
The ability to define the contacts as Schottky or Ohmic with high or low resistance is complicated by the 2-d, 1-d or quasi 1-d nature of many nanomaterials and the restricted volume of material available for engineering. Traditional techniques to engineer the contact properties inevitably alter the nanomaterial properties because of the inherently large and exposed material surface.
Nanotechnology has delivered new materials and new technologies with applications of nanotechnology will continue to expand over the coming decades. Much of the usefulness stems from effects that occur at the atomic- or nano-scale. The lead researchers, Dr. Alex M. Lord and Prof. Steve Wilks at Swansea University, were motivated to “develop a deep understanding of unique effects at these length scales that occur in nanowires and to uncover synergistic relationships such as between metal nanocatalyst particles and nanowires”, said Alex Lord. There is a natural cross over between catalysts and electrical contacts because the behaviour of both can be heavily influenced by the surface properties of the material at the edge of the interface between the particle and support.
At Swansea University we have recently shown that the electrical transport of nanocatalyst contacts on nanowires can be controlled by varying the size of the metal particle in relation to the nanowire diameter, due to quantum-mechanical tunnelling at the contact edge.[1] This was confirmed in a newly-published study with UK collaborators Dr. Quentin Ramasse and Dr. Demie Kepaptsoglou at SuperSTEM, the EPSRC funded national facility for aberration-corrected STEM, UK, and also published in Nano Letters, that developed a new experimental process (eSTEM) to directly correlate atomic-resolution electron microscopy to transport measurements on single Au-nanowire interfaces.
“The new experimental procedure has a simple premise but it was challenging to optimise and allow atomic scale imaging of the interfaces. It was essential to this study and will allow many more nanomaterials to be investigated in a similar way”, said Alex Lord who developed the experiments with Quentin Ramasse. eSTEM allowed the authors to confirm the quantum effects they described earlier by adding or removing material to the tunnelling channel at the interface edge that enhances or removes the tunnelling path. This powerful effect provides a simple method for controlling the electrical transport properties of the nanocontacts that nanodevice engineers can exploit for many devices currently being developed such as nanowire biosensors.
References:
1. Lord, A. M., Ramasse, Q. M., Kepaptsoglou, D. M., Evans, J. E., Davies, P. R., Ward, M. B. & Wilks, S. P. 2016 Modifying the Interface Edge to Control the Electrical Transport Properties of Nanocontacts to Nanowires. Nano Lett. (doi:10.1021/acs.nanolett.6b03699).
2. Lord, A. M. et al. 2015 Controlling the electrical transport properties of nanocontacts to nanowires. Nano Lett. 15, 4248–4254. (doi:10.1021/nl503743t)
Suggested Items
Inkjet Solder Mask ‘Has Arrived’
04/10/2024 | Pete Starkey, I-Connect007I was delighted to be invited to attend an interactive webinar entitled “Solder Mask Coating Made Easy with Additive Manufacturing,” hosted by SUSS MicroTec Netherlands in Eindhoven. The webinar was introduced and moderated by André Bodegom, managing director at Adeon Technologies, and the speakers were Mariana Van Dam, senior product manager PCB imaging solutions at AGFA in Belgium; Ashley Steers, sales manager at Electra Polymers in the UK; and Dr. Luca Gautero, product manager at SUSS MicroTec Netherlands.
NetVia Group Acquires Direct Imaging from Mivatek
04/09/2024 | Miva TechnologiesMiva Technologies is pleased to announce NetVia Group, Irving, TX has acquired a new Miva 2400NG Dual Tray Direct Imaging System with 30-micron capabilities for inner, outer and soldermask imaging.
Teledyne to Acquire Adimec
02/13/2024 | TeledyneTeledyne Technologies Incorporated announced that it has entered into an agreement to acquire Adimec Holding B.V. and its subsidiaries.
Real Time with... productronica 2023: MivaTek Global Advances Technology With High-res Imaging System
12/08/2023 | Real Time with...productronicaMivaTek's Brendan Hogan talks about how the company employs Digitally Adaptive Rasterization Technology (DART) in their high-res imaging equipment. He also shares how the blurred line between semiconductors and microelectronics is driving broader application of the imaging process.
Keysight Enables Validation of Arbe 4D Imaging Radar Chipset
11/30/2023 | Keysight Technologies, Inc.Keysight Technologies, Inc. announces that Arbe has selected the E8719A Radar Target Solution (RTS) to test the Arbe 4D imaging radar chipset for automotive applications.