The Heat Is On: Temperature Heals Lithium Dendrites
March 30, 2018 | Rensselaer Polytechnic InstituteEstimated reading time: 4 minutes
Researchers at Rensselaer have developed a new technique using heat to enable lithium-metal self-healing to eliminate dangerous dendrite buildup in battery anodes, paving the way for more powerful battery technologies.
Rechargeable lithium-ion, the dominant battery technology for portable electronics, is increasingly becoming the battery of choice for electric-vehicle and electric-grid energy-storage applications.
In a lithium-ion battery, the cathode (positive electrode) is a lithium metal oxide while the anode (negative electrode) is graphite. But researchers are looking for ways to replace graphite with lithium metal as the anode to boost the battery’s energy density.
Since the packing density of lithium atoms is the highest in its metallic form, batteries that use metallic lithium anodes can pack more energy per weight or volume than graphite-based anodes. However, lithium metal anodes are plagued by “dendrite” buildup that takes place over repeated cycles of charging and discharging.
Dendrites are branchlike protrusions that emanate out of the lithium metal surface. Often, they grow long enough to create a short circuit between the electrodes, leading to a fire hazard.
But now a team of researchers at Rensselaer Polytechnic Institute (Rensselaer) has discovered a way to use internal battery heat to diffuse the dendrites into a smooth layer. The researchers reported their findings this week in Science.
“We have found that lithium metal dendrites can be healed in situ by the self-heating of the dendritic particles,” said Nikhil Koratkar, the John A. Clark and Edward T. Crossan Professor of Engineering at Rensselaer and corresponding author of the paper.
Working Around the Dendrite Issue
A battery device is comprised of two electrodes — the cathode and the anode. Placed in between the electrodes is an insulating membrane that acts as a separator to prevent the electrodes from touching each other and shorting out the battery. The separator is saturated with a liquid electrolyte, which allows ions (charged atoms) to shuttle back and forth between the electrodes.
Chemical reactions produce electricity when positively charged lithium ions from the anode are transported to the cathode when discharging. When the battery is plugged into an outlet to recharge, the reverse happens: the lithium ions flow from the cathode back to the anode.
In a battery with a lithium metal anode, repeated cycles of discharging and recharging cause dendrite buildup on the anode’s surface. This thorny buildup can eventually penetrate the separator and touch the cathode. When this happens, a short circuit takes place that renders a battery inoperable, or worse, causes a fire.
Industry has avoided the lithium dendrite problem by using carbon (typically graphite) anodes. In this approach, lithium ions diffuse into and are stored within the carbon matrix, which isolates each lithium atom, thus preventing dendrite buildup. Typically, one lithium atom is stored for every six carbon atoms, with the excess carbon material serving little more than deadweight.
“Lithium-ion batteries with carbon-based anodes are the best available option, but they can no longer keep up with the storage-capacity demand,” Koratkar said. “For any significant new improvements, we must look elsewhere. The best option would be a lithium metal system.”
Self-Heating Technique Could Be a Game Changer
The Rensselaer researchers’ proposed solution takes advantage of the battery’s internal resistive heating to eliminate the dendrite buildup. Resistive heating (also known as Joule heating) is a process in which a metallic material resists current flow and, as a result, produces heat. This “self-heating” occurs through the charging and discharging process.
The researchers ramped up the self-heating effect by increasing the current density (charge-discharge rate) of the battery. The process triggered extensive surface diffusion of lithium, spreading the dendrites into an even layer.
Researchers first demonstrated this smoothening (healing) of the dendrites in a lithium-lithium symmetrical cell. They then showed the process with the same results in a proof-of-concept demonstration using a lithium-sulfur battery.
Dendrite healing would be carried out by battery management system software, which would provide doses of “self-healing” treatment by running a few cycles at a high rate of charge and discharge when an electronic device is not in use.
“A limited amount of cycles at high current density would occur to heal the dendrites, and then normal operations can be resumed,” Koratkar said. “Self-healing would occur as a maintenance strategy, long before the dendrites become a safety hazard.”
“High-density energy storage remains a critical hurdle between renewable-energy harvesting and its widespread use in everything from electrical vehicles to solar powered homes,” said Dean of Engineering Shekhar Garde. “Results from Prof. Koratkar’s lab show how the fundamental understanding of materials at the nanoscale can be employed to not only increase energy density of batteries, but also increase their life and make them safer.”
Nikhil Koratkar’s research team and lab are examples of the vision of The New Polytechnic, an emerging paradigm for teaching, learning, and research at Rensselaer, the foundation of which is the recognition that global challenges and opportunities are so great they cannot be adequately addressed by even the most talented person working alone. The New Polytechnic is transformative in the global impact of research, in its innovative pedagogy, and in the lives of students at Rensselaer.
Suggested Items
Water Management in a Large Printed Circuit Board Manufacturer
04/15/2024 | Charles Nehrig, TTM TechnologiesTTM’s environmental management is grounded in its Environmental Statement and Environmental Policy, which promote measures that make for a more responsible environmental management process. Our management system helps TTM work toward minimizing its environmental footprint and increasing the sustainability of its operations. TTM monitors its environmental performance just as it monitors its operational performance, and provides the resources required to adhere to the Company’s environmental responsibilities.
Happy’s Tech Talk #27: Integrated Mesh Power System (IMPS) for PCBs
04/08/2024 | Happy Holden -- Column: Happy’s Tech TalkA significant decrease in HDI substrate production cost can be achieved by reducing the number of substrate layers from conventional through-hole multilayers and microvia multilayers of eight, 10, 12, and more to only two layers. Besides reducing direct processing steps, the yield will increase as defect-producing operations are eliminated. The integrated mesh power system (IMPS) was invented in the latter years of MCM-D use for thin-film fabrication. Those geometries fit today into our use of ultra HDI.
Trouble in Your Tank: Supporting IC Substrates and Advanced Packaging, Part 5
03/19/2024 | Michael Carano -- Column: Trouble in Your TankDirect metallization systems based on conductive graphite or carbon dispersion are quickly gaining acceptance worldwide. Indeed, the environmental and productivity gains one can achieve with these processes are outstanding. In today’s highly competitive and litigious environment, direct metallization reduces costs associated with compliance, waste treatment, and legal issues related to chemical exposure. What makes these processes leaders in the direct metallization space?
Indium Corporation Experts to Present at SEMI THERM
03/07/2024 | Indium CorporationIndium Corporation Global Account Manager and Senior Thermal Technologist Tim Jensen and Product Development Specialist for Thermal Interface Materials Miloš Lazić will present on thermal interface material (TIM) technology at SEMI-THERM, taking place March 25–28 in San Jose, California, U.S.
Indium Corporation to Showcase Proven EV Products and High-Reliability Alloys at Productronica China
02/28/2024 | Indium CorporationAs a materials pioneer and trusted partner in electric vehicle (EV) and e-Mobility manufacturing, Indium Corporation is proud to showcase its high-reliability alloys and soldering solutions at Productronica China, March 20-22, in Shanghai.