New Superconductor Technology for the Transmission Grid
July 5, 2018 | KITEstimated reading time: 3 minutes
The German energy transition makes it necessary to extend the transmission grid. Karlsruhe Institute of Technology (KIT), to-gether with the grid operator TenneT, now studies the use of superconductor technology as an alternative to conventional power cables for short grid sections within the framework of the ENSURE Kopernikus Project. The superconductor cables de-signed by KIT for this purpose are efficient and powerful. After successful testing, they might allow for a more compact con-struction of power transmission lines in the three-phase grid.
The length of the transmission grid in Germany totals about 35,000 km. To ensure that the power produced from renewable energy sources gets to the locations where it is needed, it is planned to extend the grid by about 5,300 km in the course of the ener-giewende. Within the framework of pilot projects, underground ca-bles are planned to be used near cities and villages in particular. Major advantages could be achieved if they would be replaced part-ly by superconducting cable systems,. This is the result of a feasi-bility study carried out by KIT in cooperation with the grid operator TenneT under the Kopernikus project ENSURE. The study is planned to be completed by the end of this year and will also cover ecological and economic aspects.
The feasibility study is based on cable and cooling concepts spe-cially designed for the voltage of 380 kilovolts (kV) of the German transmission grid. “This is a big technical challenge, because super-conductor technology has never been used before on this voltage level,” says Professor Mathias Noe of KIT’s Institute for Technical Physics, who coordinates the development project. “We have now demonstrated that this is technically feasible with our new cable concepts.” The cable system is designed for a continuous power of 2,300 megawatts (MW). Losses under a high current load are signif-icantly smaller than those of a comparable above-ground line or conventional cables with a copper conductor. Superconductor tech-nology might also be advantageous in transmission line construc-tion, explains Hanno Stagge, who manages the project at TenneT: “A conventional cable system in the transmission grid requires twelve three-phase power cables. A superconducting cable system can transmit the same power with six cables.” As a result, grid oper-ators could significantly reduce the width of a line. Another ad-vantage consists in the fact that the setup of the cable compen-sates current flow in the electrical shielding layer. Consequently, no magnetic field exists outside of the cable and the cable is operated without any emissions. But it is still a long way to maturity. “After the study, the cable, including the necessary coupling sleeves and terminations, will have to be produced first. Then, it will have to be tested extensively together with a cooling system,” Hanno Stagge says. In addition, the lead time necessary to cool the cable has to be adressed.
Superconductors are materials, whose electrical resistance drops to zero when the temperature decreases below a certain point, the so-called transition temperature. As a result, these materials conduct current with hardly any losses. The new superconductor cable con-cepts for the transmission grid are based on so-called high-temperature ceramic superconductors. While conventional low-temperature superconductors have transition temperatures below 23 kelvin, i.e. minus 250°C, high-temperature superconductors have comparably high transition temperatures. With liquid nitrogen, they are cooled down to an operation temperature of about 77 kelvin, i.e. minus 196°C, and can be operated at comparably low costs, be-cause less energy is needed for cooling.
Experience gained by KIT in the “AmpaCity” cable project shows that use of superconductor technology in energy infrastructure really works. With more than one kilometer length, the AmpaCity cable is the longest high-temperature superconductor cable in the world. Since 2014, it has guaranteed efficient and stable power supply of about 10,000 households in the city of Essen with a voltage of 11 kV.
Suggested Items
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.
Trouble in Your Tank: Supporting IC Substrates and Advanced Packaging, Part 5
03/19/2024 | Michael Carano -- Column: Trouble in Your TankDirect metallization systems based on conductive graphite or carbon dispersion are quickly gaining acceptance worldwide. Indeed, the environmental and productivity gains one can achieve with these processes are outstanding. In today’s highly competitive and litigious environment, direct metallization reduces costs associated with compliance, waste treatment, and legal issues related to chemical exposure. What makes these processes leaders in the direct metallization space?