-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueThe Sustainability Issue
Sustainability is one of the most widely used terms in business today, especially for electronics and manufacturing but what does it mean to you? We explore the environmental, business, and economic impacts.
The Fabricator’s Guide to IPC APEX EXPO
This issue previews many of the important events taking place at this year's show and highlights some changes and opportunities. So, buckle up. We are counting down to IPC APEX EXPO 2024.
Getting to Know Your Designer
In this issue, we examine how fabs work with their design customers, educating them on the critical elements of fabrication needed to be successful, as well as the many tradeoffs involved. How well do you really know your customer? What makes for a closer, more synchronized working relationship?
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - pcb007 Magazine
Study on Application of Four-Wire and Four-Terminal Flying Probe Test Scheme
August 10, 2018 | Jin Erbing, Joint Stars Technology Co., LtdEstimated reading time: 6 minutes
The Problem
The traditional electrical performance conduction test is to determine the open/short circuit by the on-resistance. For example, it is generally set to 20 ohms (Ω). When the entire measured line is less than 20Ω, the line-to-line continuity of the tested line can be determined to meet the requirements. However, in actual production, some defects of the PCB circuit board, such as voids in the holes, thin copper, hole copper, and separation of the innerlayers, will affect the resistance of the circuit. The above defective boards are tested by ordinary conduction tests. The results showed that PASS, after welding or application environment changes, the line resistance will change, and even lead to open circuit. These problems will inevitably have great impact on product quality.
The Problem Analysis
The traditional electrical performance test uses the four-wire two-terminal test principle. It is impossible to measure the actual resistance of the circuit accurately. The tested resistance value includes the test pin, wire and contact resistance (R1, R2), as shown in Figure 1.
Figure 1: Traditional electrical performance test.
How can we more accurately test the resistance of the circuit under test, especially when the resistance of the circuit under test is in the order of milliohm, the test pin, wire and contact resistance cannot be omitted, and four-wire and four-terminal test must be used?
Four-Wire and Four-Terminal Test
Introduction
The four-wire and four-terminal test passes two pins on each test point, so that the test current and the measured voltage do not affect each other, and the measured resistance can be accurately measured as R=U/I (Figure 2).
Figure 2: Four-wire, four-terminal test.
Figure 2a: Four-wire four-terminal test pin structure.
The four-wire test needle technical requirements are as follows:
- The test needle blade is a pair of mirror structure, the tip error of the two blades is within 10 μm
- Insulation must be done between the two blades, and no contact short-circuit condition can occur during the test
- The distance between two blades must be controlled within 20 μm
- Test needle pressure needs to be adjusted to 10g–25g
How to Conduct Effective Testing
For hole breakage, voids, and insufficient hole copper thickness, the hole-to-hole test method is required. The test points are mainly set on both sides of the test hole. The test pins are placed on both ends of the hole. Theoretical values calculate the resistance of the hole and set the test setpoint for each hole directly, as in the calculation shown in Figure 3.
D = bore diameter
h = thickness of copper plating
d = hollow section diameter
L = depth of hole or plate thickness
Figure 3: Hole test schematic.
The formula, R=ρ.L/S, is the formula for calculating the conductor resistance. S is the cross-sectional area of the conductor. The unit is the square meter, ρ is the resistivity of the conductor material, the unit is ohm·m2/meter, and the copper is at 20°C. The resistivity was 1.75 × 10−8 ohm·m2/m, and the cross-sectional area represented is S=π [(D/2) 2 – (d/2) 2 ] = 2.19121 × 10–8m2.
Based on the above data, we can conclude:
Plate thickness of 1.6 mm, aperture 0.3 mm, copper thickness of 1 mil through-hole,
R = 1.75 × 10–8 × 1.6×10–3 ÷ 2.19121 × 10–8 = 1.28 x 10–3 ohms, or 1.28 milliohms
Page 1 of 4
Suggested Items
Indium Corporation to Present, Exhibit at EPP InnovationsFORUM
03/28/2024 | Indium CorporationIndium Corporation is set to present and exhibit at EPP InnovationsFORUM, one of Europe’s premier single-day electronics manufacturing forums, on April 17 in Leinfelden-Echterdingen, Germany. Topic areas for 2024 will include AI, automation, sustainability, and quality.
Reducing Nitrogen Consumption in Convection Soldering with Rehm Thermal Systems' Patented Mechatronic Curtain
03/28/2024 | Rehm Thermal SystemsCurrent developments indicate a need for larger throughput heights due to the trend towards e-mobility, which in turn increases nitrogen consumption for process inertization. Rehm Thermal Systems responds to this issue with an innovative solution: the mechatronic curtain.
Indium Corporation, Industry Partners to Showcase Products “Live@APEX”
03/26/2024 | Indium CorporationIndium Corporation®, in cooperation with its industry partners, will feature its proven solder solutions live on the show floor throughout IPC APEX Expo from Apr. 9‒11 in Anaheim, Calif., U.S.
ITW EAE Wins New Product Introduction Award for Electrovert® Wave Soldering Machine Deep Wave
03/26/2024 | ITW EAEITW EAE is proud to announce that it has earned a 2024 New Product Introduction (NPI) Award for Electrovert’s Deep Wave option for wave soldering machines. This new, innovative system provides the ability to pump up to a 20 mm wave height.
Mek's Next-Gen AOI Technology Takes Center Stage at IPC APEX EXPO 2024
03/19/2024 | MEKMek is excited to announce its presence at IPC APEX EXPO, North America's largest electronics manufacturing event, in Anaheim, California, from April 6-11, 2024. Attendees are invited to visit Mek at booth #1433 to explore the latest AOI technology offerings.