Powered by Windows: Enhanced Power Factor in Transparent Thermoelectric Nanowire Materials
November 7, 2018 | Osaka UniversityEstimated reading time: 3 minutes
A research group led by Professor Yoshiaki Nakamura of Osaka University successfully developed a methodology for enhancing thermoelectric power factor while decreasing thermal conductivity. By introducing ZnO nanowires into ZnO films, the thermoelectric power factor became 3 times larger than that of ZnO film without ZnO nanowires.
Image Caption: The concept to control electron and phonon transport in Embedded-ZnO nanowire structure for thermoelectric performance enhancement. In transparent materials, the increase of thermoelectric power factor and the decrease of thermal conductivity were realized due to the scattering of low-energy electrons and phonons, and the transmission of high-energy electrons. (Image: Osaka University)
For the development of high-performance thermoelectric materials, expensive and toxic heavy elements have often been used; however, the high cost and toxicity have limited the social use of such thermoelectric materials.
In this research (ACS Applied Materials & Interfaces, "Methodology of Thermoelectric Power Factor Enhancement by Controlling Nanowire Interface"), Nakamura and his team developed novel nanostructured films (Embedded-ZnO nanowire structure) composed of low-cost and environmentally-friendly ZnO. In the developed films, the thermoelectric power factor was increased by selective transmission of energetic electrons through nanowire interfaces with intentionally-controlled energy barriers, and thermal conductivity was decreased by scattering phonons at the nanowire interfaces.
It is anticipated that the success of this research will lead to the realization of high-performance transparent thermoelectric devices which will enable energy recovery from transparent objects used all over the world, such as window glass and transparent electronic devices.
Research Background
Thermoelectric generation converting heat to electricity has drawn much attention as a new energy source. Window glass with differing indoor and outdoor temperatures is anticipated as a heat source for thermoelectric generation, requiring transparent thermoelectric materials with high thermoelectric performance. Thermoelectric performance requires a high Seebeck coefficient, high electrical conductivity, and low thermal conductivity.
However, these three parameters are intercorrelated, leading to difficulty in performance enhancement. So far, expensive and toxic heavy element materials with low thermal conductivity have often been used for the development of high-performance thermoelectric materials, limiting the use of thermoelectric generation. On the other hand, low-cost and environmentally-friendly light element-based materials exhibit low thermoelectric performance due to their high thermal conductivity in general.
However, it was reported that nanostructuring achieved a significant reduction of thermal conductivity, and light element-based materials could be candidates for thermoelectric materials. But, there is still another problem in that the nanostructure scattered not only phonons but also electrons, resulting in a reduction of thermoelectric power factor.
Research Content
Nakamura and his team successfully developed low-cost and environmentally-friendly ZnO films, including surface-controlled ZnO nanowire (Embedded-ZnO nanowire structure), for the first time in the world. Embedded-ZnO nanowire structure film with high optical transmittance in visible range is anticipated as a transparent thermoelectric material.
In the structure, electron energy barrier height was controlled by modulating the dopant concentration at the nanowire interface, which enabled the increase of Seebeck coefficient due to selective transmission of high-energy electrons and scattering of low-energy electrons.
High electrical conductivity is also anticipated because the ZnO crystal is epitaxially formed at the nanowire interface, leading to relatively high electrical conductivity of high-energy electrons. Furthermore, thermal conductivity is also decreased by an increase in phonon scattering at the nanowire interface.
Embedded-ZnO nanowire structures with nanowire areal density of more than 4×109 cm-2 exhibited a thermoelectric power factor 3 times larger than that of ZnO film without nanowires. It was confirmed that the dopant concentration was modulated at the interfaces by transmission electron microscopy observation of nanowire interfaces.
The measurements of Seebeck coefficient and electrical conductivity in low temperature range (<300 K) showed the anomalous behaviors attributed to the electron transport controlled by energy barrier height. Furthermore, the energy barrier height was found to be several tens of meV through theoretical analysis of the experimental data.
In addition, thermal conductivity of the Embedded-ZnO nanowire structure was 20% smaller than that of ZnO film without nanowires because of the phonon scattering enhancement due to the introduction of the nanowire interface.
These results indicate simultaneous successes: an increase of thermoelectric power factor and a decrease of thermal conductivity. The optical measurement showed that the structure had optical transmittance of about 60% in visible range, which is comparable to the value of a window of a building.
Future Work
In the future, it will be possible to greatly decrease the thermal conductivity of Embedded-ZnO nanowire structure by increasing nanowire areal density. The thermoelectric devices composed of films with this structure are expected to be realized and see widespread use due to their use of low-cost and environmentally-friendly ZnO.
Furthermore, the concept of "Modulating energy barrier height by controlling dopant concentration" can be applied not only to ZnO but also to other promising materials, which will accelerate the development of various high-performance thermoelectric materials.
Suggested Items
Groundbreaking Ceremony Marks the Beginning of a New Era for Newccess Industrial; The Construction of the MINGXIN Building
04/12/2024 | Newccess IndustrialOn a clear and sunny day in March, the groundbreaking ceremony for the MINGXIN Building took place in Shenzhen, China. This moment marked the official commencement of construction for a project that will reshape the semiconductor materials industry.
The Need for a Holistic Global Sustainability Standard
04/10/2024 | Michael Ford, Aegis SoftwareNo one can deny that the resources of our fragile planet are finite. The environment seems like a third party, subject to constant degradation. We’re acutely aware of the effects of pollution on our climate, and despite our “throw-away” culture, recycling and recovery of materials has remained relatively expensive, even as we use more energy just to survive.
iNEMI Publishes Four Roadmap Topics
04/04/2024 | iNEMIThe International Electronics Manufacturing Initiative (iNEMI) announces the availability of the first roadmap topics in the new iNEMI Roadmap format. Printed circuit boards, sustainable electronics, smart manufacturing, and mmWave materials and test are now available online.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
Checking In With ICAPE Group
04/03/2024 | Nolan Johnson, I-Connect007ICAPE Group’s field application engineer Erik Pederson drills down on sustainability, supply chain resiliency, and what value engineering really looks like in this exclusive interview. Founded in 1999, European-based ICAPE Group provides 21 million printed circuit boards and over six million technical parts to manufacturers every month. With 30 PCB manufacturing partners globally and 50 partners providing a wide array of technical parts, ICAPE Group has operations in China, Taiwan, Thailand, South Korea, Vietnam, South Africa, Europe, Mexico, and the United States. The company also focuses on the value proposition for its customers.