Self-Sensing Materials Are Here
November 16, 2018 | ORNLEstimated reading time: 2 minutes
Carbon fiber composites—lightweight and strong—are great structural materials for automobiles, aircraft and other transportation vehicles. They consist of a polymer matrix, such as epoxy, into which reinforcing carbon fibers have been embedded. Because of differences in the mechanical properties of these two materials, the fibers can detach from the matrix under excessive stresses or fatigue. That means damage in carbon fiber composite structures can remain hidden below the surface, undetectable by visual inspection, potentially leading to catastrophic failure.
“Carbon fiber composites fail catastrophically, so you won’t see damage until the entire structure has failed,” said Chris Bowland, a Wigner Fellow at the Department of Energy’s Oak Ridge National Laboratory. “By knowing what’s going on within the composite, you can better judge its health and know if there is damage that needs to be repaired.”
Recently, Bowland and Amit Naskar, leader of ORNL’s Carbon and Composites Group, invented a roll-to-roll process to coat electrically conductive carbon fibers with semiconducting silicon carbide nanoparticles. This nanomaterial-embedded composite is stronger than other fiber-reinforced composites and imbued with a new capability—the ability to monitor its own structural health.
When enough coated fiber is embedded in a polymer, the fibers create an electrical network and the bulk composite becomes electrically conductive. The semiconducting nanoparticles can disrupt this electrical conductivity in response to applied forces, adding an electromechanical functionality to the composite.
If the composite is strained, the connectivity of the coated fibers is disrupted and the electrical resistance in the material changes. Should storm turbulence cause a composite airplane wing to flex, an electrical signal may warn the plane’s computer that the wing has endured excessive stress and prompt a recommendation for an inspection.
ORNL’s roll-to-roll demonstration proved in principle that the method could be scaled up for high-volume production of coated fibers for next-generation composites. Self-sensing composites, perhaps made with a renewable polymer matrix and low-cost carbon fibers, could find themselves in ubiquitous products, even including 3D-printed vehicles and buildings.
To fabricate nanoparticle-embedded fibers, the researchers loaded spools of high-performance carbon fiber onto rollers that dipped the fiber in epoxy loaded with commercially available nanoparticles about the width of a virus (45–65 nanometers). The fiber was then dried in an oven to set its coating.
To test the strength with which nanoparticle-embedded fibers adhered to the polymer matrix, the researchers made fiber-reinforced composite beams with the fibers aligned in one direction. Bowland conducted stress tests in which both ends of this cantilever were fixed while a machine assessing mechanical performance pushed on the beam’s middle until it failed. To investigate the sensing capabilities of the composite, he affixed electrodes on both sides of the cantilever. In a machine called a “dynamic mechanical analyzer,” he clamped one end to hold the cantilever stationary. The machine applied force at the other end to flex the beam while Bowland monitored the change in electrical resistance. ORNL postdoctoral fellow Ngoc Nguyen conducted additional tests in a Fourier-transform infrared spectrometer to study chemical bonds within the composites and improve understanding of the enhanced mechanical strength that was observed.
The researchers also tested composites made with different amounts of nanoparticles for the ability to dissipate energy—as measured by vibration-damping behavior—a capability that would benefit structural materials subjected to impacts, shakes, and other sources of stress and strain. At every concentration, the nanoparticles enhanced energy dissipation (by 65% to 257%).
Bowland and Naskar have applied for a patent for the process to make self-sensing carbon fiber composites.
“Dip coating offers a new route to utilize novel nanomaterials under development,” Bowland said.
Suggested Items
RiverSide Integrated Solutions, Inc. Celebrating 40 years of Innovation and Excellence
03/21/2024 | RiverSide Integrated Solutions, Inc.RiverSide Integrated Solutions, Inc., a pioneer in electronic and electromechanical assembly, proudly celebrates the 40th anniversary of the RiverSide name this March.
Uyemura Boosts Field and Met Lab Teams
02/21/2024 | UyemuraUyemura has announced an important field promotion, and a new addition to its Connecticut Tech Center Engineering Team. Both actions are in support of the company’s increasing focus on IC substrates, and its role as a supplier to wafer manufacturers, semiconductor fabs and PWB customers.
EMA Design Automation and Hawk Ridge Systems Reshape Landscape with Full ECAD/MCAD Convergence
02/07/2024 | EMA Design AutomationEMA Design Automation and Hawk Ridge Systems entered a strategic partnership to give customers a full ECAD/MCAD design experience, leveraging best-in-class tools and support for the entire electronic product design flow.
Ansys Collaborates with TSMC and Microsoft to Accelerate Mechanical Stress Simulation for 3D-IC Reliability in the Cloud
11/20/2023 | ANSYSAnsys has collaborated with TSMC and Microsoft to validate a joint solution for analyzing mechanical stresses in multi-die 3D-IC systems manufactured with TSMC’s 3DFabric™ advanced packaging technologies.
Cadence, Autodesk Collaborate on Smart Product Design
11/14/2023 | Cadence Design Systems, Inc.Cadence Design Systems, Inc. announced a collaboration with Autodesk to provide solutions that accelerate intelligent system design leveraging Autodesk Fusion and Cadence® PCB solutions.