A Shot in the Arm for Spintronics
May 2, 2019 | A*STAREstimated reading time: 2 minutes
A simple and efficient method for transferring the currents produced by spinning electrons from metals to semiconductors has been developed by A*STAR researchers, laying the groundwork for faster and more energy efficient spintronic computers.
Although advances in electronics have led to increasingly powerful computers, the electrical resistance of silicon limits the rate — known as the clock speed — at which computers can process information to just a few gigahertz or several operations per nanosecond.
Using the spin of electrons instead of their charge to convey information could overcome this limitation. Additionally, these so-called spin-currents consume less energy than electric currents, making spintronic computers more energy efficient than conventional electronic computers.
Transferring spin-currents from one material to another, however, has proved very challenging as the currents can become scrambled during transportation, destroying the information they carry.
Now, Justin Song from A*STAR’s Institute of High Performance Computing and colleagues from the Institute of Materials Research and Engineering, in collaboration with an international team of researchers, have developed a simple technique that significantly improves the efficiency at which spin-currents are injected from a magnetized metal into a semiconductor.
“While methods exist for spin injection from metals into semiconductors, a key issue is that they typically operate close to equilibrium,” explains Song. “As a result, when a simple ferromagnet/semiconductor interface is used, the spin injection efficiency is low.”
By heating a ferromagnet, made from cobalt, with pulses of light from a laser, the researchers were able to create spin-polarized electrons with a range of different energy levels in the cobalt, a state referred to as ‘out-of-equilibrium’, and in which their spins mostly point in the same direction.
This out-of-equilibrium state generates spin-current pulses that last less than one trillionth of a second – enough time for them to diffuse from the cobalt into a semiconductor made from single-atom layers of molybdenum disulfide, which then converts the spin-current into an electric current.
"Possibly the most striking aspect is that all this was demonstrated using a simple metal-semiconductor interface, without the complicated and costly structural engineering used in other spintronics," says Song.
The work establishes a new and simple technique for spin injection that is more than 10,000 times more efficient than what’s available now, and represents a significant step towards the development of ultrafast spintronic computers that use spin-currents as carriers of information, with clock speeds more than a thousand times faster than those in existing conventional computers.
“We are now investigating how pushing systems into an out-of-equilibrium state can lead to effects not possible at equilibrium,” says Song.
Suggested Items
KIC’s Miles Moreau to Present Profiling Basics and Best Practices at SMTA Wisconsin Chapter PCBA Profile Workshop
01/25/2024 | KICKIC, a renowned pioneer in thermal process and temperature measurement solutions for electronics manufacturing, announces that Miles Moreau, General Manager, will be a featured speaker at the SMTA Wisconsin Chapter In-Person PCBA Profile Workshop.
The Drive Toward UHDI and Substrates
09/20/2023 | I-Connect007 Editorial TeamPanasonic’s Darren Hitchcock spoke with the I-Connect007 Editorial Team on the complexities of moving toward ultra HDI manufacturing. As we learn in this conversation, the number of shifting constraints relative to traditional PCB fabrication is quite large and can sometimes conflict with each other.
Standard Of Excellence: The Products of the Future
09/19/2023 | Anaya Vardya -- Column: Standard of ExcellenceIn my last column, I discussed cutting-edge innovations in printed circuit board technology, focusing on innovative trends in ultra HDI, embedded passives and components, green PCBs, and advanced substrate materials. This month, I’m following up with the products these new PCB technologies are destined for. Why do we need all these new technologies?
Experience ViTrox's State-of-the-Art Offerings at SMTA Guadalajara 2023 Presented by Sales Channel Partner—SMTo Engineering
09/18/2023 | ViTroxViTrox, which aims to be the world’s most trusted technology company, is excited to announce that our trusted Sales Channel Partner (SCP) in Mexico, SMTo Engineering, S.A. de C.V., will be participating in SMTA Guadalajara Expo & Tech Forum. They will be exhibiting in Booth #911 from the 25th to the 26th of October 2023, at the Expo Guadalajara in Jalisco, Mexico.
Intel Unveils Industry-Leading Glass Substrates to Meet Demand for More Powerful Compute
09/18/2023 | IntelIntel announced one of the industry’s first glass substrates for next-generation advanced packaging, planned for the latter part of this decade.