Researchers Use 3-D Printer to Make New Materials
September 25, 2015 | Missouri University of Science and TechnologyEstimated reading time: 2 minutes
Missouri University of Science and Technology researchers are working to develop cyber additive manufacturing technology to create new metal materials that are stronger and lighter than conventional ones, which could make manufacturing more efficient and cheaper. The cyber manufacturing technology includes additive manufacturing process modeling, sensor network and seamless process integration.
Dr. Frank Liou, the Michael and Joyce Bytnar Professor of Product Innovation and Creativity at Missouri S&T, and Dr. Jagannanthan Sarangapani, the William A. Rutledge-Emerson Electrical Co. Distinguished Professor of Electrical and Computer Engineering at Missouri S&T, are developing cyber manufacturing technology for 3-D printers to create materials not currently in existence.
Liou and Sarangapani received a $146,758 grant from the National Science Foundation to support their research.
Structural amorphous metals (SAMs) are made through cyber-enabled additive manufacturing. Researchers us a laser to melt blown powder metal, which is deposited layer by layer to create whatever object is programmed into their computers. The trick is to get the cooling rate correct so that the metal is amorphous — that is, randomly constructed at the cellular level — instead of the natural state of crystalline formation.
Because they’re random like grains of sand on a beach, SAMs are harder, stronger and have more fracture toughness than metals in their natural state. Whereas a crystalline metal will break along its orderly cellular structure, an amorphous metal has no pattern and thus will resist breaking.
“The smaller the grains, the stronger it is,” Liou says.
The metallic glass structure of SAMs allows researchers to make materials that have low corrosive properties but high strength. The the researchers hope to show 3-D printers can make bigger and bigger parts. If they can make bigger parts, those used in industry will be stronger than those using current manufacturing processes.
Liou also says it might be possible to make a new material with 10 times the strength of a conventional one, which would mean 10 times less material would be needed to get the same strength. And that lowers the weight, size and production costs.
“If you can have the next breakthrough in materials,” Liou says, “you can have a lot of changes.”
Functionally gradient materials (FGMs) combine two metals that don’t combine easily, such as stainless steel and titanium or copper and steel. Properties of individual metals, such as thermal conductivity and mechanical strength, might be needed for an aircraft or spaceship part. “NASA is very interested” in the technology, Liou says. Sponsored by NASA’s Langley Research Center in Virginia, Liou is also working with Dr. Joseph Newkirk, associate professor of materials science and engineering, on FGM-related research.
To make the FGMs so that there is, for example, 100 percent copper on one side and 100 percent titanium on the other, the researchers have to blend them by using other metals to bridge the gap. When done, the new material — which doesn’t appear in nature — exhibits the traits of copper and titanium.
But because they’re also made with the laser, they’re formed in extreme heat.
“It’s a race with the cooling rate,” Liou says. “If you can be faster than the microstructure formation or the chemical reaction, you can fuse two metals together easily.”
Suggested Items
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.
Trouble in Your Tank: Supporting IC Substrates and Advanced Packaging, Part 5
03/19/2024 | Michael Carano -- Column: Trouble in Your TankDirect metallization systems based on conductive graphite or carbon dispersion are quickly gaining acceptance worldwide. Indeed, the environmental and productivity gains one can achieve with these processes are outstanding. In today’s highly competitive and litigious environment, direct metallization reduces costs associated with compliance, waste treatment, and legal issues related to chemical exposure. What makes these processes leaders in the direct metallization space?
AT&S Shines with Purest Copper on World Recycling Day
03/18/2024 | AT&SThe Styrian microelectronics specialist AT&S is taking World Recycling Day as an opportunity to review the progress that has been made in recent months at its sites around the world in terms of the efficient use of resources: