Excerpt: The Printed Circuit Designer’s Guide to…Flex and Rigid-Flex Fundamentals
June 25, 2018 | Dave Lackey and Anaya Vardya, American Standard CircuitsEstimated reading time: 8 minutes
Coverlayer and cover coat are terms normally reserved for flexible circuit constructions and they are by default a defining structural element of both flex and rigid flex circuits. Coverlayers serve as a flexible solder mask of sorts, protecting the delicate circuits from damage and potential wicking of solder along circuit traces, while leaving open access to design features where interconnections are to be made to components by soldering.
It is important to determine the thickness of a coverlayer to allow for maximum flexibility when desired, and ensure you have chosen a coverlayer with a sufficient amount of adhesive on it to accommodate the copper weight. Coverlayers are also of importance in the design of areas where the circuit is to be bent either just one time, intermittently, or dynamically, millions or even billions of times over its useful life. The latter case, the dimensions and make of the flexible circuit coverlayer is critical. In dynamic flex circuits, there is need to balance the amount of flexible materials on the sides of the conductors where flexing is to occur. It is important to know and understand that there are different types of materials available for use as coverlayer materials, and that there is no single, ideal solution. These material choices include: materials that are laminated to the copper circuits using heat and pressure; materials that can be laminated and then pho toimaged, like solder mask, to define points of connection; and materials that are simply screen printed on to seal traces, while leaving open features of interest for further processing or for making interconnections.
Number of Flex Layers
The clear majority of flexible circuits have just one or two metal layers. However, an increasing number of high-performance products now require high layer counts and high density interconnect (HDI) design techniques. As layer count increases, so does the need for control in design generation to accommodate manufacturing process realities. It is also worth noting, while on the topic of layer count, that stiffness increases as a cube of thickness. That is, if one doubles its thickness, the stiffness goes up eightfold (23 = 8), and thus small increases in thickness due to increases in layer count can greatly decrease circuit flexibility. The converse is also true, of course. The following are some key concerns to be understood and addressed in the design process relative to flex layer count.
As is the case with any multilayer construction, core thickness must be provided with the assumption that copper is clad on at least one surface. The core thickness is generally understood to be the thickness of the dielectric material between the copper layers. The core material can be a simple single-sided piece of copper clad polymer, or it can be clad with copper on both sides. Many different core thicknesses are commonly available for flexible circuits, but the most common is 75 mm, typically comprised of 25 mm of base polymer (e.g., poly imide, polyester) with 25 mm of adhesive (e.g., acrylic, modified epoxy) on either side to bond copper foil to the surface of the base polymer. Thinner and thicker core materials can be procured both with and without adhesive. It is recommended that designers check with their flex vendors for both their recommendations and the availability of the chosen material.
While the discussion so far been limited to flexible circuit core material, rigid materials are employed in the fabrication of rigid-flex circuits. Of course, any of the myriad core materials used in rigid multilayer circuits are also available to make rigid-flex circuits. However, once again, it is advisable to check with the flex manufacturer for advice as to what options are most common and readily available.
Separation Distance Between Flex Circuit Cores
When a product requires two or more cores, there is a need to define in the specification what the spacing requirements are between cores. The spacing can impact product performance (physical and electrical) and, most obviously, thickness. In some designs, the spacing between flex circuit cores may be filled with dielectric material, but with other designs the dielectric between flex cores in the flex area may be omitted to assure maximum flexibility (Figure 2).
Figure 2: Bonded vs. unbonded flex.
If the core layers must be unbonded, this should be noted in the documentation. Those areas where bonding is to be avoided should be identified in the design artwork package. The unbonded areas must have a coverlayer applied to each exposed side (Figures 2 and 3). In laminated areas, it is not required and arguably a liability when plated through-hole reliability through the assembly process is considered. Obviously, in areas where interconnection is required between multiple layers of internal circuits, a dielectric is required as shown in Figure 2. In the next installment we will continue this three-part series by addressing circuit layup symmetry, designing for bending, and controlled impedance.
Dave Lackey is vice president of business development at American Standard Circuits.
Anaya Vardya is CEO of American Standard Circuits.
This article originally appeared in the April 2018 issue of Flex007 Magazine, click here.
Suggested Items
Indium Experts to Present on High-Temperature, Lead-Free Solder Paste and High Reliability Liquid Metal Alloys Poster at ECTC
05/16/2024 | Indium CorporationIndium Corporation Research Associate Kyle Aserian will deliver a presentation at the 74th Electronic Components and Technology Conference (ECTC) on May 31, in Denver, Colorado.
Indium Experts to Present at Electronics in Harsh Environments SMTA Conference
05/13/2024 | Indium Corporationndium Corporation Technical Manager for Europe, Africa, and the Middle East, Karthik Vijay, will deliver a technical presentation and Indium Corporation Senior Technologist, Dr. Ronald Lasky, will deliver both a workshop and technical presentation at the Electronics in Harsh Environments SMTA Conference on May 14-16 in Copenhagen, Denmark.
Connect the Dots: Designing for Reality—The Pre-Manufacturing Process
05/08/2024 | Matt Stevenson -- Column: Connect the DotsI have been working with Nolan Johnson on a podcast series about designing PCBs for the reality of manufacturing. By sharing lessons learned over a long career in the PCB industry, we hope to shorten learning curves and help designers produce better boards with less hassle and rework. Episode 2 deals with the electronic pre-manufacturing process. Moving from CAD (computer-aided design) to CAM (computer-aided manufacturing) is a key step in PCB manufacturing. CAM turns digital designs into instructions that machines can use to actually build the PCB.
AIM Solder Signs Shinil Fl Ltd. as New Distributor for Korea
05/08/2024 | AIM SolderAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce a new distribution partnership with Shinil Fl Ltd., a prominent supplier of technological solutions in the SMT and semiconductor sectors.
Indium Corporation to Showcase HIA Materials at ECTC
05/07/2024 | Indium CorporationAs an industry leader in innovative materials solutions for semiconductor packaging and assembly, Indium Corporation® will feature its advanced products designed to meet the evolving challenges of heterogeneous integration and assembly (HIA) and fine-pitch system-in-package (SiP) applications at the 74th Electronic Components and Technology Conference (ECTC), May 28‒31, in Denver, Colorado.