Happy Holden on Gerry Partida’s ‘Significant’ Microvia Reliabilty Paper
December 30, 2022 | Happy Holden, I-Connect007Estimated reading time: 2 minutes
Gerry Partida, vice president of technology at Summit Interconnect, authored a technical paper, “Next Progression in Microvia Reliability Validation—Reflow Simulation of a PCB Design Attributes and Material Structural Properties During the PCB Design Process,” at IPC APEX EXPO 2022, and it’s worth revisiting. This significant paper on microvia reliability validation provides a summary of what’s been happening in the microvia fabrication arena, especially regarding the issue of latent defects in stacked microvias. The paper is available for download here.
Partida offers a thorough look at the controversy initiated in 1996 when latent electrical defects began showing up in field-deployed boards using microvias. My familiarity with this topic dates to 2000, when IPC organized round robin testing of microvia technologies. All looked good, and HDI technology took off. As evolution would have it, the technology grew and diversified. But all the new variants were not necessarily tested like the initial round in 2000.
As Gerry summarizes, “Today, the industry is facing a similar challenge with microvia reliability, especially after reflowing of the PCB at assembly, during rework, or operating in the field. As with the shortcomings of electrical testing in the past, the industry designed PCBs with microvias without evaluating the thermal properties of the material or the geometries in the design. Fabricators produced the finished goods and evaluated the finished PCB to established performance standards such as IPC-6012. When difficult-to-detect failures occurred post assembly, a test method IPC-TM-650 2.6.27 was established and a caution was added to the IPC- 6012 Rev E in Section 3.6, Structural Integrity. The testing of a D coupon via IPC-TM-650 2.6.27 did validate that the finished PCBs were safe for assembly, but it did not stop a fabricator from building a bad design.”
Many studies have shown that the failures seem to be initiated at the interface of the microvia target pad and the plated microvia interface—a plain “butt joint.” As the elevated temperature of lead-free assembly reflow is employed, the stress on this joint exceeds what it can accommodate, unlike tin-lead reflow that occurs at a lower temperature. What caught us unprepared is that after reflowing, the joint appears to be okay and will pass other performance testing, waiting until it fails in the field. This explanation seems to be validated by research that iMEC in Europe has conducted for the European Space Agency. Their finite element analysis of the microvia structure shows the maximum stress at this location and the stress increases as you stack the microvias and increase the temperature.
To read this entire article, which appeared in the November 2022 issue of Design007 Magazine, click here.
Suggested Items
AIM Solder Signs Shinil Fl Ltd. as New Distributor for Korea
05/08/2024 | AIM SolderAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce a new distribution partnership with Shinil Fl Ltd., a prominent supplier of technological solutions in the SMT and semiconductor sectors.
The Knowledge Base: A CM’s Perspective on Box Build Practices
04/30/2024 | Mike Konrad -- Column: The Knowledge BaseIn the ever-evolving landscape of electronics manufacturing, the box-build process stands out as a critical phase that bridges the gap between individual component manufacturing and the delivery of a fully functional electronic system. This intricate procedure, encompassing the assembly of everything from PCBs to wire harnesses and mechanical enclosures, demands a high level of precision, efficiency, and innovation. As the electronics assembly industry expands and diversifies, understanding the best practices within box-build assembly has become paramount for manufacturers aiming to stay ahead in a competitive market.
Latest Test and Inspection Solutions from GOEPEL electronic at SMTconnect 2024
04/29/2024 | GOEPEL electronicGOEPEL electronic will be demonstrating automated test and inspection equipment at SMTconnect, taking place in Nuremberg from June 11 to 13, 2024.
Determining the Value-add of Box Build
04/24/2024 | Nolan Johnson, I-Connect007At a strategic level, adding box-building services makes sense for customer loyalty. But is it really that simple? Jon Schmitz, who manages customer engagement at RiverSide Integrated Solutions, talk about about what it really takes to be successful in offering EMS and final assembly services under the same company banner.
IMAPS & IPC to Host Onshoring Workshop
04/16/2024 | IPCThe International Microelectronics Assembly and Packaging Society (IMAPS) and IPC will host an Onshoring Workshop to discuss ongoing progress and forward-looking strategies to drive the Onshoring Advanced Packaging and Assembly, April 29 – May 1, 2024, in Arlington, Virginia.