Innovative New Uses for Ceramic Column Grid Arrays from TopLine
December 18, 2015 | Andy Shaughnessy, I-Connect007Estimated reading time: 8 minutes
TopLine President and CEO Martin Hart sat down to discuss his paper on ceramic column grid arrays (CCGA) at the recent SMTA International show in Chicago. Hart begins by explaining the relationship between CCGA and ball grid arrays (BGA), and TopLine's drive to find new uses for CCGA.
Andy Shaughnessy: Martin, why don't you start by giving us a little background on CCGAs.
Martin Hart: The best way to talk about CCGAs is to reference their cousin, the BGA. Everybody is familiar with BGA—ball grid arrays. Few people realize that the CCGA, the ceramic column grid array, was actually invented about ten years before the first BGA. When BGA first came out, they were invented by Bell Laboratories; a full ten years after columns had already been in the field. The main purpose of having a column instead of a solder ball is to extend reliability. You get more temperature cycles out of a solder column because it will absorb the CTE mismatch between the materials of ceramic and substrate, such as an FR-4 PC board.
Shaughnessy: We just don't hear much about CCGA. Everybody seems to have settled on the BGA and flip chips and various other sorts of packaging. Why did the CCGA fall out of favor?
Hart: That's a good question. BGAs are lower cost and much easier to assemble. During the manufacturing process, attaching a solder ball is significantly easier than attaching a column. Solder balls roll and self-center onto the BGA pads. Columns are difficult to attach to the pads. They don't self-center because they are held rigidly in place, usually by a graphite tool, during the column attach process. Columns can easily get bend if handled incorrectly.
Shaughnessy: You have to literally stand this thing up.
Hart: You have to stand the column straight up during the attachment of the column to the substrate.
Shaughnessy: It sounds very risky, in a way.
Hart: There is an element of risk, but it’s more of a situation of having a correct manufacturing process. Your process has to be dialed to effectively use column grid arrays. Once you have a process in place, then CCGA seems to work well.
Shaughnessy: What is the new use that you seem to have found for them?
Hart: First I’ll tell you the traditional places where column grid arrays are used. Traditionally, they've been used in defense, military, aerospace and also in high-value computing. One new area is down-hole drilling, where you have electronics going down several miles. It's very hot as you go below the earth’s surface. There is also interest in specialized automotive where you have electronics in the firewall. Also, columns can be are found in some medical. Not medical implants in a human body, but in medical equipment. There is a benefit to use CCGA wherever you have a large ceramic package, and mounted on an FR-4 board or a polyimide board. CCGA is more reliable when the temperature swings dramatically.
If you have a very small ceramic, it's safe to use a BGA. I've researched and wrote some tables and calculations showing when it is safe to use a ceramic BGA and when you must use a CCGA. A small 15 mm square ceramic BGA will not cause any problem with solder ball delamination. But if you start to go larger, say a 35 mm square, 40 mm square, 45 mm or even larger, 50 mm square, then solder balls will delaminate. That will effectively create a catastrophic failure in the equipment.
I also want to point out that your equipment does not even have to be electrically switched on. Say, if your equipment is turned off, sitting in storage, then if you have a large ceramic part mounted with solder balls on an FR-4 board, then that equipment might fail. If your equipment is out in the elements experiencing alternating hot and cold temperatures, then your equipment might fail if it contains large ceramic BGA components. When the sun goes down, temperatures might drop -25 to -40°. And when the sun comes up temperatures might rise 100-125°. Just sitting in the box, you'll see the phenomenon of delamination with large ceramic BGA components.
Shaughnessy: What led you to focus more on CCGA?
Hart: The original business of TopLine was to manufacture process development kits of all kinds of parts, from BGA and QFP in a kit form with circuit boards. Customers, particularly in mil-defense, were asking for column grid arrays so they could perform their own process development. This has gone on for a number of years and we decided, "Okay, we need to jump in and address this market of producing CCGA and solder columns."
Shaughnessy: I guess CCGA would have its own completely different process.
Hart: Yes, it does. The process of attaching a column onto a ceramic substrate is totally different than attaching solder balls to a BGA. CCGA requires a graphite fixture to hold the column upright at a 90° angle. It involves having a controlled reflow process. We found that vapor phase reflow ovens are best solution because your maximum temperature is fixed. You can also use a twelve-zone oven, but you have to have that oven profile really dialed to attach solder columns.
Shaughnessy: How tall is this column?
Hart: Oh, good question. Traditionally, columns are 2.2 mm high. There's nothing totally magical about 2.2 mm high. Columns have been made 1.27 mm, which is 50 mills. Columns have been made bigger in diameter and smaller in diameter. IBM set the standard years ago with studies and of papers showing that 2.2 mm, is a good column height. The industry settled ever since. The secret is actually in the attachment process. You start with a longer column and then trim it down to 2.2 mm during the planarization process. After all the columns are attached in an array, you literally have to cut the columns shorter to planarize them. So you wind up with 2.2 mm, but you start off with a column that is 2.3 mm, up to 2.5 mm, in order to wind up with 2.2mm.
Page 1 of 2
Suggested Items
Indium Experts to Present on High-Temperature, Lead-Free Solder Paste and High Reliability Liquid Metal Alloys Poster at ECTC
05/16/2024 | Indium CorporationIndium Corporation Research Associate Kyle Aserian will deliver a presentation at the 74th Electronic Components and Technology Conference (ECTC) on May 31, in Denver, Colorado.
Indium Experts to Present at Electronics in Harsh Environments SMTA Conference
05/13/2024 | Indium Corporationndium Corporation Technical Manager for Europe, Africa, and the Middle East, Karthik Vijay, will deliver a technical presentation and Indium Corporation Senior Technologist, Dr. Ronald Lasky, will deliver both a workshop and technical presentation at the Electronics in Harsh Environments SMTA Conference on May 14-16 in Copenhagen, Denmark.
Connect the Dots: Designing for Reality—The Pre-Manufacturing Process
05/08/2024 | Matt Stevenson -- Column: Connect the DotsI have been working with Nolan Johnson on a podcast series about designing PCBs for the reality of manufacturing. By sharing lessons learned over a long career in the PCB industry, we hope to shorten learning curves and help designers produce better boards with less hassle and rework. Episode 2 deals with the electronic pre-manufacturing process. Moving from CAD (computer-aided design) to CAM (computer-aided manufacturing) is a key step in PCB manufacturing. CAM turns digital designs into instructions that machines can use to actually build the PCB.
AIM Solder Signs Shinil Fl Ltd. as New Distributor for Korea
05/08/2024 | AIM SolderAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce a new distribution partnership with Shinil Fl Ltd., a prominent supplier of technological solutions in the SMT and semiconductor sectors.
Indium Corporation to Showcase HIA Materials at ECTC
05/07/2024 | Indium CorporationAs an industry leader in innovative materials solutions for semiconductor packaging and assembly, Indium Corporation® will feature its advanced products designed to meet the evolving challenges of heterogeneous integration and assembly (HIA) and fine-pitch system-in-package (SiP) applications at the 74th Electronic Components and Technology Conference (ECTC), May 28‒31, in Denver, Colorado.