Focus on Smart Processes, Not Just Smart Factories
March 2, 2021 | Nolan Johnson, PCB007Estimated reading time: 2 minutes
Nolan Johnson talks to Audra Thurston, Todd Brassard, and Meredith LaBeau about how Calumet is focusing on smart processes, and not as much on smart factories. While modern manufacturing equipment and next-gen technologies can be impressive, so much innovation still hinges on human beings. Calumet believes by investing in their workforce and instilling a culture of innovation throughout their company and supply chain, they’ll see faster advancement.
Nolan Johnson: Right now, there’s a whole lot of discussion about smart factories and equipment that help you automate your manufacturing processes. But right behind that is all of the “basic blocking and tackling” work that needs to be done to manage processes. How do you tackle process improvement to make them more efficient and make them better?
Todd Brassard: A relevant question, especially if the resurgence in domestic manufacturing continues. There is pressure, newfound interest, and good reason for U.S. OEMs to manufacture leading electronics technologies within the United States. Much of this new interest is coming from increasing security concerns as other countries rapidly advance their technical capabilities – at times through forced technology transfer, intellectual property theft, or other nefarious methods – which in many cases already exceeds the manufacturing capabilities of United States electronics industry.
Sure, there’s good reason to bring electronics manufacturing back to U.S. soil, but lawmakers’ focus on advancing and protecting exclusively microelectronics as opposed to the greater surrounding ecosystem has ended in a domestic electronics industry that can readily conceive and design, but not adequately manufacture, the most advanced electronic systems at home in the United States. Through direct and frequent interactions, we know defense, aerospace, and even some commercial U.S. OEMs are casting about the country seeking circuit board manufactures that can provide viable technological solutions for novel leading edge electronic systems to fulfill their government contract commitments within the next two to three years. Often, will little success, according to their representatives on the calls.
Money solves problems by enabling manufacturers to acquire modern equipment, attract talented people, and sustain a capable workforce, but unlike the state sponsored circuit board manufacturers common in China, the U.S. government cannot and will not come to rescue of the U.S. circuit board manufactures with a sweeping injection of funding. Manufacturers must play with the “cards they been dealt” and make incremental improvements from there.
How then can U.S. circuit board manufacturers begin the journey towards becoming a smart factory? Is becoming a smart factory a good strategy based on what the U.S. market is now asking of its electronic manufacturing industrial base? Is there a middle ground between traditional manual processing and smart factories, say with smarter processes?
To read the full article, which appeared in the January 2021 issue of PCB007 Magazine, click here.
Suggested Items
Book Excerpt: The Printed Circuit Assembler’s Guide to... Factory Analytics
04/24/2024 | I-Connect007 Editorial TeamIn our fast-changing, deeply competitive, and margin-tight industry, factory analytics can be the key to unlocking untapped improvements to guarantee a thriving business. On top of that, electronics manufacturers are facing a tremendous burden to do more with less. If you don't already have a copy of this book, what follows is an excerpt from the introduction chapter of 'The Printed Circuit Assembler’s Guide to... Factory Analytics: Unlocking Efficiency Through Data Insights' to whet your appetite.
Listen Up! The Intricacies of PCB Drilling Detailed in New Podcast Episode
04/25/2024 | I-Connect007In episode 5 of the podcast series, On the Line With: Designing for Reality, Nolan Johnson and Matt Stevenson continue down the manufacturing process, this time focusing on the post-lamination drilling process for PCBs. Matt and Nolan delve into the intricacies of the PCB drilling process, highlighting the importance of hole quality, drill parameters, and design optimization to ensure smooth manufacturing. The conversation covers topics such as drill bit sizes, aspect ratios, vias, challenges in drilling, and ways to enhance efficiency in the drilling department.
Elevating PCB Design Engineering With IPC Programs
04/24/2024 | Cory Blaylock, IPCIn a monumental stride for the electronics manufacturing industry, IPC has successfully championed the recognition of the PCB Design Engineer as an official occupation by the U.S. Department of Labor (DOL). This pivotal achievement not only underscores the critical role of PCB design engineers within the technology landscape, but also marks the beginning of a transformative journey toward nurturing a robust, skilled workforce ready to propel our industry into the future.
Winner of The Science Show Rakett 69 Receives Incap Scholarship
04/24/2024 | IncapThe winner of the Rakett 69 science show, Andri Türkson, who stood out as an electronics enthusiast, received a scholarship from Incap Estonia, along with an internship opportunity in Saaremaa.
Alternative Manufacturing Inc. Awarded QML Requalification to IPC J-STD-001 and IPC-A-610
04/24/2024 | IPCIPC's Validation Services Program has awarded an IPC J-STD-001 and IPC-A-610 Qualified Manufacturers Listing (QML) requalification to Alternative Manufacturing Inc (AMI).