Bismuth-based Nanoribbons Show 'Topological' Transport, Potential for New Technologies
January 20, 2016 | Purdue UniversityEstimated reading time: 5 minutes
A key finding was that the researchers documented the use of nanoribbons to measure so-called Aharonov-Bohm oscillations, which is possible by conducting electrons in opposite directions in ring-like paths around the nanoribbons. The structure of the nanoribbon - a nanowire that is topologically the same as a cylinder - is key to the discovery because it allows the study of electrons as they travel in a circular direction around the ribbon. The electrons conduct only on the surface of the nanowires, tracing out a cylindrical circulation.
“If you let electrons travel in two paths around a ring, in left and right paths, and they meet at the other end of the ring then they will interfere either constructively or destructively depending on the phase difference created by a magnetic field, resulting in either high or low conductivity, respectively, showing the quantum nature of electrons behaving as waves,” Jauregui said.
The researchers demonstrated a new variation on this oscillation in topological insulator surfaces by inducing the spin helical mode of the electrons. The result is the ability to flip from constructive to destructive interference and back.
“This provides very definitive evidence that we are measuring the spin helical electrons,” Jauregui said. “We are measuring these topological surface states. This effect really hasn’t been seen very convincingly until recently, so now this experiment really provides clear evidence that we are talking about these spin helical electrons propagating on the cylinder, so this is one aspect of this oscillation.”
Findings also showed this oscillation as a function of “gate voltage,” representing another way to switch conduction from high to low.
“The switch occurs whenever the circumference of the nanoribbon contains just an integer number of the quantum mechanical wavelength, or ‘fermi wavelength,’ which is tuned by the gate voltage of the electrons wrapping around the surface,” Chen said.
It was the first time researchers have seen this kind of gate-dependent oscillation in nanoribbons and further correlates it to the topological insulator band structure of bismuth telluride.
Page 2 of 3
Suggested Items
The Chemical Connection: Reducing Etch System Water Usage, Part 2
05/02/2024 | Don Ball -- Column: The Chemical ConnectionIn my last column, I reviewed some relatively simple ways to reduce water usage in existing etch systems: cutting down cooling coil water flow, adding chillers to replace plant water for cooling, lowering flow rate nozzles for rinses, etc. This month, I’ll continue with more ways to control water usage in your etcher. Most of these are not easily retrofittable to existing equipment but should be given serious consideration when new equipment is contemplated. With the right combination of add-ons, it is possible to bring the amount of water used in an etch system to almost zero.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.