Sun-Soaking Device Turns Water into Superheated Steam
December 12, 2018 | MITEstimated reading time: 5 minutes
MIT engineers have built a device that soaks up enough heat from the sun to boil water and produce “superheated” steam hotter than 100 degrees Celsius, without any expensive optics.
On a sunny day, the structure can passively pump out steam hot enough to sterilize medical equipment, as well as to use in cooking and cleaning. The steam may also supply heat to industrial processes, or it could be collected and condensed to produce desalinated, distilled drinking water.
The researchers previously developed a sponge-like structure that floated in a container of water and turned the water it absorbed into steam. But a big concern is that contaminants in the water caused the structure to degrade over time. The new device is designed to be suspended over the water, to avoid any possible contamination.
The suspended device is about the size and thickness of a small digital tablet or e-reader, and is structured like a sandwich: The top layer is made from a material that efficiently absorbs the sun’s heat, while the bottom layer efficiently emits that heat to the water below. Once the water reaches the boiling point (100 C), it releases steam that rises back up into the device, where it is funneled through the middle layer — a foam-like material that further heats the steam above the boiling point, before it’s pumped out through a single tube.
“It’s a completely passive system — you just leave it outside to absorb sunlight,” says Thomas Cooper, assistant professor of mechanical engineering at York University, who led the work as a postdoc at MIT. “You could scale this up to something that could be used in remote climates to generate enough drinking water for a family, or sterilize equipment for one operating room.”
The team’s results are detailed in a paper published today in Nature Communications. The study includes researchers from the lab of Gang Chen, the Carl Richard Soderberg Professor of Power Engineering at MIT.
A Clever Combination
In 2014, Chen’s group reported the first demonstration of a simple, solar-driven steam generator, in the form of a graphite-covered carbon foam that floats on water. This structure absorbs and localizes the sun’s heat to the water’s surface (the heat would otherwise penetrate down through the water). Since then, his group and others have looked to improve the efficiency of the design with materials of varying solar-absorbing properties. But almost every device has been designed to float directly on water, and they have all run into the problem of contamination, as their surfaces come into contact with salt and other impurities in water.
The team decided to design a device that instead is suspended above water. The device is structured to absorb short-wavelength solar energy, which in turn heats up the device, causing it to reradiate this heat, in the form of longer-wavelength infrared radiation, to the water below. Interestingly, the researchers note that infrared wavelengths are more readily absorbed by water, versus solar wavelengths, which would simply pass right through.
For the device’s top layer, they chose a metal ceramic composite that is a highly efficient solar absorber. They coated the structure’s bottom layer with a material that easily and efficiently emits infared heat. Between these two materials, they sandwiched a layer of reticulated carbon foam — essentially, a sponge-like material studded with winding tunnels and pores, which retains the sun’s incoming heat and can further heat up the steam rising back up through the foam. The researchers also attached a small outlet tube to one end of the foam, through which all the steam can exit and be easily collected.
Finally, they placed the device over a basin of water and surrounded the entire setup with a polymer enclosure to prevent heat from escaping.
“It’s this clever engineering of different materials and how they’re arranged that allows us to achieve reasonably high efficiencies with this noncontact arrangement,” Cooper says.
Page 1 of 2
Suggested Items
Altus Equips SSTL with Advanced Cleaning Technology for Electronics
05/07/2024 | Altus GroupAltus Group, a leading supplier of capital equipment for the electronics manufacturing industry, has announced the successful installation of an advanced PCBA cleaning system at Surrey Satellite Technology Limited (SSTL).
ZESTRON Academy Launches 2024 Advanced Packaging & Power Electronics Webinar Series
05/01/2024 | ZESTRONZESTRON, the leading global provider of high-precision cleaning products, services, and training solutions in the electronics manufacturing and semiconductor industries, proudly announces the launch of its highly anticipated webinar series on Advanced Packaging & Power Electronics, a webinar series on the latest innovations, cleaning, and corrosion challenges.
KYZEN Announces Exclusive Partnership with Manufacturers’ Representative Restronics Florida
04/25/2024 | KYZEN'KYZEN, the global leader in innovative environmentally responsible cleaning chemistries, proudly announces its strategic partnership with Manufacturers’ Representative Restronics Florida. Just like KYZEN’s commitment to continuously improving precision cleaning, Restronics Florida serves as a consultative OEM sales representative organization dedicated to educating customers to enhance their processes and productivity.
KYZEN to Promote Pair of Stencil Cleaning Chemistries at SMTA Ciudad Jaurez Expo & Tech Forum
04/25/2024 | KYZEN'KYZEN, the global leader in innovative environmentally friendly cleaning chemistries, will exhibit at the SMTA Ciudad Juarez Expo & Tech Forum, scheduled to take place Thursday, May 9, 2024 at the Injectronic Convention Center in Ciudad Jaurez, Chihuahua, Mexico. During the event the KYZEN Clean Team will focus on understencil cleaning products KYZEN E5631J and CYBERSOLV C8882.
KYZEN to Focus on AQUANOX A4618 at SMTA Wisconsin Expo & Tech Forum
04/22/2024 | KYZEN'KYZEN, the global leader in innovative environmentally friendly cleaning chemistries, will exhibit at the SMTA Wisconsin Expo & Tech Forum, scheduled to take place Tuesday, May 7, 2024 at the Four Poins by Sheraton, Milwaukee Airport in Milwaukee, WI.