EIPC Technical Snapshot: Automotive Technology
October 19, 2020 | Pete Starkey, I-Connect007Estimated reading time: 7 minutes
In his example, the LED package had a coefficient of thermal expansion (CTE) of 10 ppm/°C, whereas that of the aluminium base was 23 ppm/°C. The CTE mismatch was reduced by using a low-CTE aluminium alloy (19 ppm/°C), and the dielectric was re-formulated to lower its elastic modulus so that it effectively became a compliant inter-layer. An additional benefit of the re-formulation was to increase its maximum operating temperature to 155°C. The outcome was that the modified IMS material enabled the LED headlight to exceed 3,000 thermal cycles without failure.
The final presentation, entitled “Today’s Multilayer PCB Requirements for the Automobile Industry,” came from Multiline International Europa Managing Director and EIPC Board Member Paul Waldner. He also used a see-through motor car illustration to demonstrate the extent to which numerous electronic systems had become fundamental to the operation of the vehicle.
This time the focus was on how the automobile sensed its environment and how it would need to become increasingly networked: vehicle-to-vehicle, vehicle-to-cloud, vehicle-to-infrastructure, vehicle-to-pedestrian, vehicle-to-road-sign, and vehicle-to-drone. He remarked that tomorrow’s automobiles would incorporate many elements of industrial development.
Inputs, processing, and outputs would be controlled with a high-performance server, and high-frequency PCBs would be an essential requirement for vehicle radar and lidar and for supporting ultra-fast communications. There was a convergence of technologies in multilayer PCB requirements for the communications, military, and automobile industries because of the signal-speed requirements of 5G communication networks and distance-to-hazard sensing in the development of autonomous vehicles. PCBs for future automobiles would require high circuit density and high layer counts with different materials—some of which would demand very high lamination temperatures. High reliability was fundamental.
Waldner considered that there were three necessities for managing the technology convergence: better pressing technology, better layer to layer registration of multilayers, and better signal integrity for high-speed circuits. He discussed the principles and details of a proprietary lamination press, with induction heating offering uniformity of temperature throughout the stack and the benefits of accurate control of parameters and low power consumption. Although the four-slot tooling system had been established for many years, he believed that it still offered many advantages, particularly when laminating mixed materials with different expansion coefficients.
And regarding signal integrity, the track geometry of fine-line designs could be controlled to precise limits with a proprietary modified semi-additive process using an ultra-thin palladium catalyst layer to initiate electroless copper deposition. His example showed 20-micron traces on a 50-micron pitch with a square cross-section.
A question-and-answer session followed the presentations and raised points for discussion on the subjects of stacked microvia reliability, SAC alloys for automotive applications, and high-frequency challenges, to which the experts responded readily. Emma Hudson did a skillful job of moderating the session and keeping the whole proceedings within the scheduled one-hour time slot. Thanking the speakers for their contribution and the audience for their attention, she announced that further technical snapshot webinars are planned for November 18 and December 19.
Page 2 of 2Suggested Items
Indium Corporation Expert to Present on Pb-Free Solder for Die-Attach in Discrete Power Applications
04/30/2024 | Indium CorporationIndium Corporation Product Manager – Semiconductor Dean Payne will present at the Advanced Packaging for Power Electronics conference, hosted by IMAPS, held May 8-9 in Woburn, Massachusetts, USA.
Taiyo Circuit Automation Installs New DP3500 into Fuba Printed Circuits, Tunisia
04/25/2024 | Taiyo Circuit AutomationTaiyo Circuit Automation is proud to be partnered with Fuba Printed Circuits, Tunisia part of the OneTech Group of companies, a leading printed circuit board manufacturer based out of Bizerte, Tunisia, on their first installation of Taiyo Circuit Automation DP3500 coater.
Vicor Power Orders Hentec Industries/RPS Automation Pulsar Solderability Testing System
04/24/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, is pleased to announce that Vicor Power has finalized the purchase of a Pulsar solderability testing system.
AIM Solder’s Dillon Zhu to Present on Ultraminiature Soldering at SMTA China East
04/22/2024 | AIMAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce that Dillon Zhu will present on the topic: Ultraminiature Soldering: Techniques, Technologies, and Standards at SMTA China East. This event is being held at the Shanghai World Expo Exhibition & Convention Center from April 24-25.
AIM to Highlight NC259FPA Ultrafine No Clean Solder Paste at SMTA Wisconsin Expo & Tech Forum
04/18/2024 | AIMAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce its participation in the upcoming SMTA Wisconsin Expo & Tech Forum taking place on May 7 at the Four Points by Sheraton | Milwaukee Airport, in Milwaukee, Wisconsin.